Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Small Silvertone Phonograph
#1

I have always thought these were neat and tried to get one off eBay several years ago. Sadly they always went kinda high. The ones I found around here were usually beat to death, missing lids, or partially crushed and in scrap hoppers due to their metal construction. Well, in an Amish antique shop of all things, I finally found a nice example![attachment=2][attachment=1][attachment=0]

Even the handle is in good shape and looks almost like new. It has a three tube amp inside and though needing some cleaning out, looks good inside. Shouldn't be expensive to redo. Recap job, new cartridge, maybe a little conditioning of the idler wheel. I just think these little guys are neat and it goes well with my 1948 Silvertone radio-phono-wire recorder console. Oh, gotta get the speaker reconed in that! Icon_problem

No matter where you go, there you are.
#2

A little update, the phonograph is now working! Had the caps and electrolytics replaced and the motor lubed up. The cartridge is fine, anyone know what these cartridges are in the Silvertone phongraphs of this era? I have a couple and my friend has had several and they never seem to die. They can't be magnetic can they? Only issue is they use the cursed 'permanent' stylus. So, when the stylus wears out you have to replace the whole shot. Only other issue is the spindle acts too large for several 78's. I've never run into that issue before with a 78 rpm phonograph. Might have to take some fine grit sandpaper and polish the spindle some more.

No matter where you go, there you are.




Users browsing this thread:
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently no members online.

>