Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Latest acquisition
#1

Thanks to my friend Ed in Ohio, I now have this neat addition to the collection:

[Image: http://philcoradio.com/gallery2/images/1...age_00.jpg]

A Model 43B, from June 1932. Philco's first complete, all-in-one all-wave receiver.

Anyone else find anything new/neat/unusual in the Philco line lately?

--
Ron Ramirez
Ferdinand IN
#2

Oooo! Beauty!
#3

Hi All,
Nice radio Ron. A fine catch! At the end of July I picked up a Philco 90 for $65.00. A lot was wrong upon inspection. The (tiger stripe)? veneer is mostly gone but the rest is o.k. The primary on the first detector coil was open. The speaker field coil was open also. The filter choke along with the output transformer were open too. The tunning cap had to be cleaned also.The choke and output transformer were ordered from Radio Daze along with a #47 tube. The detector coil break was on the first loop. The speaker field I wound with #36 guage wire. I only had a little over a half pound which gave me 2600 ohms so I put a 10W 500 ohm resistor in series. You talk about tough getting the speaker core out! Wow. I drilled and tapped a 1/4 bolt to hold it in. After a rebuild of the cap blocks, a few resistors and electrolytics it plays great!!
Last friday the wife and I went back to the same place and there sat another 90! I got this one for $43.00. It rained here all day Saturday so I tore into this one. Not much wrong but a lot of recapping and resistors. hopefully I can power up tomorrow. The chassis has a lot of rust though. Will have to start cleaning after I get it playing.

Terry
#4

Hmph! Some people have all the luck! Icon_biggrin

Great buys on your 90 sets. Now would you consider letting go of the rusty one? Icon_lol Just kidding of course. Congrats!

--
Ron Ramirez
Ferdinand IN
#5

Ron,
Thank you. I am kind of proud of them. By the way #2 is up and running Icon_lol

Terry
#6

Now, another acquisition:

This set came from the Olney auction this past Sunday.

[Image: http://www.philcoradio.com/images/phorum...ff/112.jpg]

It is a 112 Bel Geddes lowboy, has some minor veneer issues, and the knobs - well, two of the knobs are 1937-40 Philco, the tuning knob is from an RCA, and the off-on knob is missing. Cloth is not original. The chassis is the later version with push-pull Type 47 outputs (one of the Type 47 tubes is missing).

The price: $20. No-one bid against me. Oddly enough, other consoles brought more money than this one did.

A friend of mine says I "stole" this at the $20 price. What say you guys?

--
Ron Ramirez
Ferdinand IN
#7

Dang...!!! Very nice catch. Icon_eek
#8

Ron,
Your lucky I wasnt at that auction. Looks like its "philco season".
Nice finds!




Users browsing this thread:
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently 2310 online users. [Complete List]
» 1 Member(s) | 2309 Guest(s)
Avatar

>