1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 48-200 help
Danny
Member
***
Posts: 64
Threads: 22
Joined: Oct 2006
City: Acworth State, Province, Country: GA
#1

12-01-2006, 04:08 PM
Low volume and garbles. Down to looking at Z300. Removed it and found Z300D and Z300C not in the can. R300 is in there and found 470K actually at 54K so I'll replace it, but what do I do with the missing caps? Should I put them in or leave as is. Funny thing is, it doesn't look like the I.F. can has ever been messed with, prior to my fat fingers intruding that is. Schematic at the following link....

http://www.nostalgiaair.org/PagesByModel...013627.pdf
Danny
Find
Chuck Schwark
Phorum Expert
*****
Posts: 1,703
Threads: 55
Joined: Sep 2005
City: Evanston, IL
#2

12-01-2006, 08:28 PM
I assume you mean C300C and C300D, both are 100 pF caps which, with R300, comprise the 10kHz audio "tweet" filter.

Strange they would be missing. Putting in new silver-mica types back in certainly won't hurt.

Be sure that 2nd. IF can has a part no. of 32-3952, according to the parts list. Maybe the set had an early repair/replacement in its llife and that can is same IF freq. but different part number.
Chuck Schwark,
The Philco Repair Bench
[Image: http://www.philcorepairbench.com/images/philog3tiny.gif]
http://www.philcorepairbench.com
Website Find
Danny
Member
***
Posts: 64
Threads: 22
Joined: Oct 2006
City: Acworth State, Province, Country: GA
#3

12-03-2006, 10:46 AM
Thanks for the info Chuck. Part # on the can is 32-3952. I'll go ahead and install them as you suggest.
Danny
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration