Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Schematic for a 14B - Never mind
#1

Does anybody have a clear schematic for a 14B?

It's done.

Thanks
#2

I'll bet Chuck does. I need to get one too. The one on NA really bad. From the looks of it it ought to be a great playing set. One rf amp, two if amps, and three stages of audio... Plus a shadowgraph. I've got the 14 modern version.
Terry
#3

I'm about 3/4 of the way through this one now. by the time I find a ledgable schematic, I won't need it. I'll let you know in the morning how well it works.

Interesting that a lot of the dogbone resistors in this one seem to have drifted down rather than up, or they were lower to start with and did not drift (much).

Yes, a 42 driving 2 more in PP. Should be loud, anyway.
#4

Yes, Phlogiston, I have an original Model 14 Service Bulletin No. 176, in my archives,
and all published Production Change Notes from Philco. Shadow Meter info as well.

Regards,
Chuck
#5

Thanks guys, but it is all done, just takes a couple of hrs longer without a good schematic. It is hard to tell which contacts are used in the Bakelite caps without one.

It is a very nice radio. Picked up lots of stations with only a 18" antenna.




Users browsing this thread:
[-]
Recent Posts
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM
The list of my radio & TV collection!
Magical chords of forgotten melodies, old nostalgic music on an old radio... Saturday night blues on the Mid-Waves on an...RadioSvit — 12:20 PM
Philco 42-345 Restoration/Repair
Thank you MrFixr55 the issue with this radio is that the internal coil antenna is missing and there was a wire in its pl...osanders0311 — 11:34 AM
Philco 610B oscillator wiring
Regarding the oscillator circuit which is comprised of the 6A7's cathode, control grid, and screen grid. These elements ...Radioroslyn — 10:33 AM
Philco 42-345 Restoration/Repair
Hi OSanders, First off, welcome to the Philco Phorum where Phine Phamily-Phriendly Pholks Phull of Philco Phacts and P...MrFixr55 — 08:41 AM
Philco 42-345 Restoration/Repair
Today I've been reading through the site trying to learn more about this radio. I also soldered the lose power cord cabl...osanders0311 — 08:24 PM

[-]
Who's Online
There are currently 2404 online users. [Complete List]
» 1 Member(s) | 2403 Guest(s)
Avatar

>