Posts: 2,023
Threads: 365
Joined: Jun 2010
City: Dover, OH
Here is the Emerson console radio I purchased earlier today. It will definitely need work and the guy was lucky he didn't start a fire by trying to play it! The underside of the chassis was crammed full of stuff from chipmunks! Anyways, it is a seven tube console and the tube compliment is: 80, 47, 2A6, 58, 58, 58, 56. The speaker is a Utah speaker that looks to weigh more than the chassis. I can't find a model number on this unit, just a serial tag on the chassis.
No matter where you go, there you are.
Posts: 1,107
Threads: 88
Joined: Jun 2011
City: Tacoma
State, Province, Country: Washington
I believe this may be your beastie..
http://www.nostalgiaair.org/PagesByModel...004742.pdf Emerson Model 77
Posts: 2,023
Threads: 365
Joined: Jun 2010
City: Dover, OH
That looks like it! Thanks! 
No matter where you go, there you are.
Posts: 3,122
Threads: 57
Joined: Apr 2011
City: Lexington, KY
Yep, it looks like a 77.
[Image: http://img.photobucket.com/albums/v348/j...rson77.jpg]
Nice snag, there aren't a whole lot of Emerson consoles floating around out there.
John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
Posts: 2,023
Threads: 365
Joined: Jun 2010
City: Dover, OH
Thanks for the advertisement picture, Elliot! So far I have not stumbled on any pictures of existing model 77 consoles, just pictures taken from advertisements like that one. I would not have gone for this radio if it hadn't been such a rare piece. I know where two slightly later Emerson consoles are sitting in storage, but have been afraid to ask the guy what he wants for them. Both are in nice shape.
No matter where you go, there you are.
Posts: 4,639
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
Judging by the schematic it looks like a fairly straightforward radio to work on, a single band and about ten paper caps and two electrolytics to replace. It also has a tuned RF amplifier stage so it's probably a reasonable performer. I think the biggest issue will be repairing or replicating that grille, but it looks like the front panel could be removed to work on it.
Regards
Arran
Posts: 1,107
Threads: 88
Joined: Jun 2011
City: Tacoma
State, Province, Country: Washington
Jayce,
Be sure to send a pic of this rare set to Radio Attic Archives.
Posts: 7,248
Threads: 266
Joined: Dec 2009
City: Roslyn Pa
That's where I looked and couldn't find it.
Terry
Posts: 1,107
Threads: 88
Joined: Jun 2011
City: Tacoma
State, Province, Country: Washington
But if he sends the pic, it will be there for the next person. 
Posts: 2,023
Threads: 365
Joined: Jun 2010
City: Dover, OH
Hmm, I will have to check the site out and do that. Hope they don't mind a picture of a sort of rough looking Emerson.
No matter where you go, there you are.
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
That's a nice snag, Jay!!!
Although I hate to say "I told you so," I am going to do it anyway!
Radios ALWAYS come around. A couple of months ago you were not having any good luck. NOW you ARE!!!!
 
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
Cannot Adjust an IF Transformer’s cores
|
| It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM |
|
PT-6 antenna connections
|
| I seem to have lost my way on this PT-6.
I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM |
|
40-150 General questions
|
| Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM |
|
40-150 General questions
|
| I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM |
|
40-150 General questions
|
| It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM |
|
40-150 General questions
|
| Hi Kevin,
No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM |
|
Philco 38-7 Speaker
|
| 7K should be fine. While not a perfect match (This transformer is meant for 6V6 tubes), Antique Electronic Supply (AES)...MrFixr55 — 08:03 AM |
|
40-150 General questions
|
| I discovered a stamp on the underside of the breadboard on my Philco 40-150. It is"56-1417' in black ink with numbe...Kevin_D — 07:14 AM |
|
Philco 38-7 Speaker
|
| FYI the Impedance of the HR20 (the one I have) secondary of the audio transformer is 5 ohms. The 38-7XX speaker is suppo...tludka — 04:22 PM |
|
Philco 38-7 Speaker
|
| Yeah, don't use the transformer currently on the H-20 (Dopf, I thought "H20, is that new technology, a speaker usin...MrFixr55 — 03:51 PM |
|
Who's Online
|
There are currently 2307 online users. [Complete List]
» 1 Member(s) | 2306 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
