Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 45
#1

Hi All;
I went and did it, I got another chassis.. Chassis seem to be about all I can afford with shipping and all.. I got a Philco 45, it was listed as a Philco 29 45, but the label of the Back of it shows a 45.. Don't know anything about it, it should be here by the end of the week..
I though that having a two bander might simpliify my getting something working and my troubleshooting and aligtnment skills.. I can leave it on the broadcast band and see about making it work.. I will update everyone once it gets here..
The 28, 29, 39, and 45 have all the same/similiar front end all being a two bander, the only exception is the converter tube used.. 1C6 vs 6A7..
THANK YOU marty
#2

The 1C6 is a tube for a battery-operated radio. Battery sets are simple and easy to fix. Building a power supply is easy too since there are innumerable ways of doing it.
#3

Hi All;
Bill. If you have kept up with all of my postings on my Battery set Philco 34, that uses the 1C6, you would notice that I am and have had innermable trouble with it.. Which Is part of the Reason that I am getting the Philco 45, something simplier to try and get going..
I have a Power Supply that is great for my 34.. (Home built)
THANK YOU marty
#4

Hi All;
I Got the Philco 45 and Speaker today.. I found out After posting about a transformer that He had the Speaker for it, so I got it..
Its quite Dusty and Dirty.. So I will need to do some cleaning up..
I will Replace the Electrolytics and see with my Variac what happens..
Then I will replace a Cap at a Time, making sure that I have it wired correct and it isn't any worse.. I think that is part of some of my problems with my Philco 34.. Just letting Everyone know.. For Now until I can get the funds I will use the pages from Nostalgiaair, then get a set from Chuck when I am able to afford it..
THANK YOU Marty
#5

Hi All;
Well, Considering what I have, I feel I am very Blessed.. I replaced the three electrolytic Caps and put it on the Variac..
I got a station very weak and with lots of squeeling, but it was there..
But, after, a minute or so I suddenly hear a pop! and I have no sound..
So, for a first try, I feel that what I got is Great !!!
THANK YOU Marty




Users browsing this thread:
[-]
Recent Posts
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM

[-]
Who's Online
There are currently 2855 online users. [Complete List]
» 3 Member(s) | 2852 Guest(s)
AvatarAvatarAvatar

>