1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco TPA-1
PhilcoFordTesla
Junior Member
**
Posts: 49
Threads: 3
Joined: Oct 2019
City: Shingle Springs State, Province, Country: CA
#76

11-15-2019, 09:03 PM
        OK, motor extracted from the foam rubber goo, ready for microprobing!  looking at rc car motors if this doesn't pan out 24mm series 280? IIRC need to check movie night
Find
PhilcoFordTesla
Junior Member
**
Posts: 49
Threads: 3
Joined: Oct 2019
City: Shingle Springs State, Province, Country: CA
#77

11-16-2019, 12:43 AM
    TPA-1 Replacement motor? 24mm diameter with 2MM shaft should be perfect with the right torque curve 1/2 the rpm of some others
Find
PhilcoFordTesla
Junior Member
**
Posts: 49
Threads: 3
Joined: Oct 2019
City: Shingle Springs State, Province, Country: CA
#78

11-16-2019, 01:21 AM
or maybe this one, ordered one of each while I attempt to dissect the original


Attached Files Image(s)
   
Find
Jake Blake
Banned
Posts: 816
Threads: 25
Joined: Mar 2014
City: Louisville, KY
#79

11-16-2019, 02:11 AM
"All my stuff usually seemed to work better while they were/it was still apart! lol "   Icon_lol
Find
PhilcoFordTesla
Junior Member
**
Posts: 49
Threads: 3
Joined: Oct 2019
City: Shingle Springs State, Province, Country: CA
#80

11-16-2019, 02:15 AM
    tried to retension the brushes but still no continuity, armature looks burned
Find
PhilcoFordTesla
Junior Member
**
Posts: 49
Threads: 3
Joined: Oct 2019
City: Shingle Springs State, Province, Country: CA
#81

11-16-2019, 08:32 PM
Just got done replacing C1, .mp3 player sounds pretty decent!  Might keep it on for a while, hope it doesn't need heat sinks on those big 'ol outputs??  Time for the infra-red gun . . maybe better tone with the cabinet closed up . . . 

https://youtu.be/bEtvu4ldFts

rock & roll!
Find
PhilcoFordTesla
Junior Member
**
Posts: 49
Threads: 3
Joined: Oct 2019
City: Shingle Springs State, Province, Country: CA
#82

06-16-2024, 11:03 PM
picked up a second one, and went back and re-read some tips needed for my first, any love left here for TPA-1's?
Find
morzh
Odobenus rosmarus
*****
Posts: 15,818
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
#83

06-17-2024, 09:02 PM
In all honesty, other than it being rare, it is a fairly crappy player.
Badly made too.

On the other hand, why don't you make your own thread?
This one is Tim's and has been getting older by the day.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
PhilcoFordTesla
Junior Member
**
Posts: 49
Threads: 3
Joined: Oct 2019
City: Shingle Springs State, Province, Country: CA
#84

06-17-2024, 11:47 PM
yeah just nostalgia for me as dad gave me one of the amps as a functional toy back ~1956 now i have a second one looking back i have an intermittent on the board of the first, trying to get motivated to clear the bench and lay into it.  yeah its a crappy player i'd like to just have the amp out breadboarding something to just 'watch it work!' lol thx for the reply new thread someday
Find
« Next Oldest | Next Newest »




Users browsing this thread:
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration