1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 16B noise suppression circuit pot
fields 100
Member
***
Posts: 228
Threads: 64
Joined: Dec 2013
City: Northbrook, IL
#1

08-16-2014, 05:44 PM
Does anyone know off hand the wattage of the #82 pot? It is 10K,it's bad and I have not powered the set yet to calculate it.

http://www.nostalgiaair.org/PagesByModel...013139.pdf
(This post was last modified: 08-16-2014, 05:45 PM by fields 100.)
Find
Mondial
Phorum Expert
*****
Posts: 1,114
Threads: 14
Joined: Feb 2013
City: Irvington, NY
#2

08-16-2014, 06:44 PM
Look like the original is probably a 2 Watt wirewound?

Under normal operation, the pot dissipates only 0.16 Watt, but at turn on its quite a bit more. Before all the tubes heat up, there is almost 500 V across the voltage divider, and the pot is subject to about 100 V. Calculating the power (100 x 100 / 10000 ), it is 1 Watt under those conditions, so to be conservative I would go with a 2 Watt replacement
(This post was last modified: 08-16-2014, 06:45 PM by Mondial.)
Find
fields 100
Member
***
Posts: 228
Threads: 64
Joined: Dec 2013
City: Northbrook, IL
#3

08-16-2014, 07:10 PM
That 's great. I have already ordered 5W, but was not sure. The original is wire wound. The new one will fit nicely.
Thanks.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
Thanks Gary.dconant — 12:16 PM
New Philco Repair Bench
I tried accessing the site through our library and got the same response. It's reported to our tech gurus. GaryGarySP — 11:50 AM
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM

[-]
Who's Online
There are currently 5078 online users. [Complete List]
» 3 Member(s) | 5075 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration