Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

My new A52CK
#1

Got this today finally! An A52CK Philco clock radio.

The guy said restored but geeze [Image: http://www.antiqueradios.com/forums/imag...lleyes.gif] 

Stripping it 98%, leaving spots of original lacquer on it and then painting brown paint with a small brush around the darker toned areas is not restoration........

Will have to redo in the spring. I still love it and thanks again Jim.  Icon_shh


Kirk


Attached Files Image(s)
       

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#2

Good looking radio Kirk. With your talent I'm sure it will be done right.
#3

Kirk;
  I knew what it would be like the first time you posted a link to that auction, a typical "antique mall" style restoration, or what I call a "strip n' clearcoat" job, there are a few of those sorts of radios on my nearby craigslist sites. If you know what to look for it's very difficult for them to hide, no toners, a flat lifeless look, pits from open grain.
Regards
Arran
#4

When I spotted the radio I reasoned ..not a horrible starting point...and a not so easy model to find.
Id rather find them absent toner than colored incorrectly so at least I can see the veneer I have to work with and in this case all the wood looks good and solid without any surprises as opposed to buried with toner or even worse...stained. Work some cabinet magic on this and it will be really pretty. I also like this version of the model better than the other
http://radioattic.com/item.htm?radio=0150114
#5

I just died!!!!!!

There are 2!!!! versions!!!!

Icon_e_surprised Icon_e_surprised Icon_e_surprised

Now I am back on the hunt  Icon_lolno  Icon_lol 

Thanks a lot Jim,  Icon_mrgreen

Kirk

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM
38-10T chassis Restoration begins
It is acceptable but not desirable. Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM

[-]
Who's Online
There are currently 4252 online users. [Complete List]
» 1 Member(s) | 4251 Guest(s)
Avatar

>