1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
How To Remove Dial Pointer - 38-12
RQuam
Junior Member
**
Posts: 4
Threads: 2
Joined: May 2015
City: Sedro-Woolley WA
#1

05-01-2015, 10:15 PM
Could someone give me advice on how to remove the dial pointer on a Philco 38-12? The pointer needs to come off so I can remove and clean smoker residue from the tuning capacitor.

Richard
Find
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#2

05-01-2015, 10:19 PM
It just pulls off. You may have to twist it back and forth a bit (carefully, while holding the tuning condenser plates fully meshed; that is, closed) but it should just pull off. In case of corrosion, do be careful...
--
Ron Ramirez
Ferdinand IN
Find
RQuam
Junior Member
**
Posts: 4
Threads: 2
Joined: May 2015
City: Sedro-Woolley WA
#3

05-01-2015, 10:24 PM
Thanks, Ron. That worked. I was being too careful before.

Richard
Find
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#4

05-02-2015, 07:58 AM
Nothing wrong with being too careful - that is preferred to the "bull in a china shop" method. Icon_wink Good luck! Icon_thumbup
--
Ron Ramirez
Ferdinand IN
Find
klondike98
Phorum Moderator
******
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#5

05-02-2015, 09:45 AM
Welcome to the Phorum Richard!!!
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
RQuam
Junior Member
**
Posts: 4
Threads: 2
Joined: May 2015
City: Sedro-Woolley WA
#6

05-02-2015, 11:48 AM
Thanks, Bob. I originally joined a couple years ago but didn't visit the forum for several months. Then, when I tried to log on, I had forgotten my password and couldn't get a new one because my email address had changed. So...I rejoined.

Richard
Find
Eric Adams
Phorum Expert
*****
Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages State, Province, Country: Florida
#7

05-02-2015, 12:57 PM
Welcome, Richard Icon_thumbup  Good luck with your 38-12
Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

Website Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
Apparently there is a new Philco Repair Bench found at https://philcoradio.com/repairbench/ When I try to go to order a ...dconant — 12:00 PM
Philco 60 Squealing
Well, a wave trap is a trimmer in series with the coil so at the resonant frequency it provides a short to ground. This ...RodB — 10:07 AM
Philco 60 Squealing
Rod, My radio is run 7. The wave trap is on that schematic as shown in the picture. dconant — 09:21 AM
American Bosch Model 802 auto radio
Hi Arran ,  Thanks for your help with this radio.And especial thanks for letting me know to look it up under United Ame...Antipodal — 04:32 AM
Philco 60 Squealing
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM
Philco 60 Squealing
I just peaked it for the best signal at 600. NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration