Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 46-1201 Phono Cartridge
#1

See post #3 below for information on a cartridge for a Philco 46-1209 radio-phono.

Meanwhile, enjoy some photos of Greg's 46-1209 with gold accents on the knobs, hand applied.

- admin



   

   

   

   

   

Greg V.
West Bend, WI
Member WARCI.org
#2

May I ask where one may locate a replacement needle and cartridge for a Philco 46-1201? I love this model and the technology involved. And it's one of my most wanted units.  

Ian M. Gordon
NEARC
HARPS
#3

This is the go-to place for cartridges and idler wheels for me: http://www.thevoiceofmusic.com/

I hand painted the gold on the knobs of my 46-1201. Really dresses them up. I do that on Hippo models too, which use the same knobs.

Greg V.
West Bend, WI
Member WARCI.org
#4

That model No. from VM is KCCC. It's a barrel type with both 78 and LP styli. It has a higher output voltage than other's you might use. I believe the output volts. are 1.3 volts. I just ordered one yesterday.
#5

Since Jim added some useful information regarding the phono cartridge for this model, I decided not to delete the entire thread, even though the radio has been sold. I will leave it up to the moderators if they wish to leave this thread or delete the whole thing.

Greg V.
West Bend, WI
Member WARCI.org
#6

Per Greg's suggestion, I have converted this thread from a "for sale" ad into a restoration topic.

--
Ron Ramirez
Ferdinand IN
#7

Thanks, Ron.

Greg V.
West Bend, WI
Member WARCI.org




Users browsing this thread:
[-]
Recent Posts
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM

[-]
Who's Online
There are currently 4794 online users. [Complete List]
» 3 Member(s) | 4791 Guest(s)
AvatarAvatarAvatar

>