Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

What to do with Photofinish to preserve it
#1

Here is the Motorola 61CA I've been struggling with. As you can see, the Photofinisher is just about perfect. The border around the top (the flat part of the top is also Photofinisher) is painted in brown tone...it just looks like paint to me. What I'd like to do with it is give it a good cleaning all around, re paint that border, and just give it a good polishing. I can just tape off the Photofinisher without hurting it, yeah? And I can just spray lacquer on the painted part and leave the Photofinisher alone?

Those push buttons are cool, though. They have no electronic parts. They Physically turn the tuning cap to the presets and the adjustment is a screw that lengthens or shortens the part that comes in contact with the cam of the  tuning cap.

   

Charlie in San Antonio
#2

If it is tight under the clear then yes you can use good tape and work on the surrounding areas.


Kirk

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#3

I have gently cleaned photofinish and then sprayed lacquer over t with excellent results.
#4

Steve!
Where ya been?

Me

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#5

I've been around, but that four letter word (work) keeps getting in the way!  My restorations are at a slow pace because of it.  Hopefully it will slow  up in the winter. 




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Delco car radio Peko vibrator converstion issues
Rich, There is an Australian website (Cool386.com) that has much useful info regarding repair and restoration of vibr...Joe Rossi — 07:29 PM
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM

[-]
Who's Online
There are currently 3831 online users. [Complete List]
» 4 Member(s) | 3827 Guest(s)
AvatarAvatarAvatarAvatar

>