Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

TWO 16b tombstones/ FINISHED!
#46

 Not sure Art, If I  remember right I was told that they used both styles of nobs and there for didn't matter. I also looked at a bunch of 16bs online and seen both styles of nobs on both early and late versions. Ron would know for sure, I think Ron would have given me a Icon_thumbdown  if there where a discrepancy in that department Icon_think   
#47

Quote: I think Ron would have given me a [Image: http://philcoradio.com/phorum/images/smi...mbdown.gif]  if there where a discrepancy in that department [Image: http://philcoradio.com/phorum/images/smi..._think.gif]   
Yeah, I got "thumbs down" on knobs one time. Icon_lol    Seriously, I'm happy to have Ron critique my work.
Steve

M R Radios   C M Tubes
#48

  I just noticed I have 4 stars now under my belt (senior member Icon_think ) Icon_clap Icon_crazy Icon_crazy Icon_crazy Icon_crazy Icon_crazy  I don't see how when I cant apply decals properly Icon_think
#49

(06-14-2015, 11:35 PM)Fred Taylor Wrote:    I just noticed I have 4 stars now under my belt (senior member Icon_think ) Icon_clap Icon_crazy Icon_crazy Icon_crazy Icon_crazy Icon_crazy  I don't see how when I cant apply decals properly Icon_think

HeHe.. The stars depends on how many times you have posted on here.
#50

Hi,

Very nice job on the model 16Bs.. two of my favorite radio models.

I have seen the late 16B with either three lower older-style hex knobs or three of the newer styled round knobs. The upper knob on the late set should always be the newer concentric style (the older hex style knob would not fit!). Same goes for the 16X versions from June & Nov 1934.

Now, having seen this mix of knobs on some later versions does not make it certain that they came from the factory this way, though it seems likely, as so many of the late models are seen this way.

One other point that just occurs to me, seeing Fred's empty cabinets side by side. The upper knob cut-out for the later set has larger diameter than for the earlier set, as needed to accommodate the concentric knobs of the later chassis versus the single retractable knob of the earlier version. Has anybody noticed if the later-cabinets fitted with earlier chassis had the smaller diameter cut-out?? This would for sure indicate they must have come from the factory this way. The converse does not necessarily prove anything, of course.

Paul
#51

Those 16B's look absolutely exquisite! Fantastic job!

Slave to an RCA Victor CTC-25




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently no members online.

>