Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

37-61 Knobs Question
#1

I have looked at photos of 37-61 sets on ARF and Radio Museum. But I still cannot tell what color KNOBS it should have. My example came with BROWN knobs, even though the escutcheon is BLACK. Can anyone tell me what color the knobs SHOULD BE on this radio?

Another question on the knobs: I noticed in my stock of Philco knobs of this type (thin with knurled or grooved edge) I find ones with PLAIN front and others with a POINTER. Does anyone know what type of knob is correct for this radio? It has 3 such knobs: left (on-off and tone), center (band), and right (volume). Perhaps a mix?

Finally, what direction should the speaker transformer be oriented? Mine came with the transformer at 9:00, but I have seen other examples at 12:00 and even 6:00.

Thanks!
#2

Quote:I have looked at photos of 37-61 sets on ARF and Radio Museum. But I still cannot tell what color KNOBS it should have. My example came with BROWN knobs, even though the escutcheon is BLACK. Can anyone tell me what color the knobs SHOULD BE on this radio?

Brown. Only the 1936 Philcos used black knobs in this pattern.

Quote:Another question on the knobs: I noticed in my stock of Philco knobs of this type (thin with knurled or grooved edge) I find ones with PLAIN front and others with a POINTER. Does anyone know what type of knob is correct for this radio? It has 3 such knobs: left (on-off and tone), center (band), and right (volume). Perhaps a mix?

All three should have a pointer. If your radio was a Model 37-60, it would have a single tuning knob (not the dual concentric type as on your 37-61), and it would not have a pointer.

Quote:Finally, what direction should the speaker transformer be oriented? Mine came with the transformer at 9:00, but I have seen other examples at 12:00 and even 6:00.

I don't think it really matters, as long as the audio output transformer does not physically interfere with anything such as the tuning condenser or dial lamp. Icon_smile

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640.  Does that help?--Johngeorgetownjohn — 02:14 PM
two videos to watch VHS and history of TV
Hello Every, Here are a couple videos right up my alley VHS and the history of Television . history of VCR VHS Hi...radiorich — 02:13 PM
Made mistake & did not label connection
You haven't given us the model number of the set so I looked up the 6A8 pin assignment. Pin 8 is the cathode and pin 7 i...RodB — 01:19 PM
Made mistake & did not label connection
Happy Thanksgiving all! I have made a real bonehead mistake this time. Hope someone can help.  I am trying to determi...georgetownjohn — 12:51 PM
New Philco Repair Bench
Apparently there is a new Philco Repair Bench found at https://philcoradio.com/repairbench/ When I try to go to order a ...dconant — 12:00 PM
Philco 60 Squealing
Well, a wave trap is a trimmer in series with the coil so at the resonant frequency it provides a short to ground. This ...RodB — 10:07 AM
Philco 60 Squealing
Rod, My radio is run 7. The wave trap is on that schematic as shown in the picture. dconant — 09:21 AM
American Bosch Model 802 auto radio
Hi Arran ,  Thanks for your help with this radio.And especial thanks for letting me know to look it up under United Ame...Antipodal — 04:32 AM

[-]
Who's Online
There are currently 2219 online users. [Complete List]
» 2 Member(s) | 2217 Guest(s)
AvatarAvatar

>