Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Lost thread
#1

Well, this is interesting. Seems that I have misplaced the thread I had going here about the 600 padder in my silvertone chassis I'm trying to ressurect. Was here last night when I shut the computer off. JUst started up and it's gone. Anybody have any idea how that could happen. And is there any way to get it back?
#2

see pm

sam

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#3

(06-15-2016, 01:26 PM)sam Wrote:  see pm

sam

Does soft mean the software did it? And if so how?
#4

Hi leftwing,
I think you had "soft deleted" that thread. That means its been deleted from view for everyone except moderators and administrator. We look at it and most often go ahead and permanently delete it to free up space. Looking at the logs I was the guy that deleted it. I assumed you deleted it because you found the answer to your question. Sorry about that. Please just start a new thread on it. I don't recall your question but seem to remember it was something I might have been able to answer. And if I can't, I'm sure someone here can.
#5

Oh...and the software does not soft delete it without the check box in the upper right of the post getting checked and the soft delete button getting pushed. If you are on a phone, sometimes things get accidentally pushed....
#6

Thanks for the update, Bob. On my screen there is a delete box in the lower right corner with a red x in it. Would that be the one? I wanted to delete the post I had put up and thought that was what that was for. Could that have deleted the whole thread? Ed
#7

You are right, I see a little different screen than you do. Yes the red X DELETE box will delete the post. It shows up to moderators as a "soft" delete. If you delete the first post in a thread, I believe it will delete the entire thread.
#8

Looking back at the moderators log, I can't tell for certain what happened but it may be that i should have recognized your delete was going to kill the entire thread. If I had realized that I would have restored it. Unfortunately I did not and the thread is now gone...very sorry! Icon_redface




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently no members online.

>