1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Knobs for Philco 52-1731
Southpaw
Junior Member
**
Posts: 3
Threads: 1
Joined: Mar 2018
City: Denver, CO
#1

03-05-2018, 12:50 PM
Hello: I'm restoring a Philco 52-1731 cabinet and am missing 2 of the 4 tuning knobs. Any suggestions on where to obtain 2 of these could be much appreciated. Images of the knobs are attached. Thanks!


Attached Files Image(s)
   
Find
Nathan Slingerland
Super Moderator
******
Posts: 1,872
Threads: 212
Joined: May 2015
City: Seattle State, Province, Country: WA
#2

03-05-2018, 12:56 PM
Welcome to the Phorum!

For the knobs check with Gary at http://oldradioparts.com (looks like he's closed until 3/11).
Find
Southpaw
Junior Member
**
Posts: 3
Threads: 1
Joined: Mar 2018
City: Denver, CO
#3

03-05-2018, 01:19 PM
Thank you, Nathan! I will reach out to Gary next week...
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,248
Threads: 266
Joined: Dec 2009
City: Roslyn Pa
#4

03-05-2018, 10:54 PM
Philco Knobs & Pushbuttons (original)

David Frush (original and NOS knobs, including many for Philco sets)

Julie McCall - Original knobs for Philco and other radios.

Kelton Trammell - Original knobs for Philco and other radios.

Mark Oppat's Old Radio Parts

Mike Koste - Gobs of Knobs

Here at the Philco Phorum we have a Resource section has listed parts and services available for Philco sets.
Personally have had dealings w/ Julie and Mike both are top notch!

Welcome to the Phorum.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
Southpaw
Junior Member
**
Posts: 3
Threads: 1
Joined: Mar 2018
City: Denver, CO
#5

03-06-2018, 12:13 PM
Much appreciated, Terry
Find
Arran
Phorum Expert
*****
Posts: 4,639
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#6

03-09-2018, 01:43 AM
Or you could keep your eyes open for a smashed early 50s Philco plastic radio or junker radio-phono combo, many of those use the same style of knobs.
Regards
Arran
Find
« Next Oldest | Next Newest »




Users browsing this thread:
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration