Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

General Electric Old and New
#1

I mentioned I got a GE AA5 from a pal at work, cabinet is cleaned up, epoxiied inside and about done. The numberson the dial are fragile and I am not going to clean in that spot anymore not to rub them off. No model number and I have not found it in an archive yet.

On another GE note featured are 2 probably early eighties models recently found on the bay. Rare for me to go there and rarer to buy. I needed a better portable and this looked clean and the little table set fits on my small kitchen table. Both are surprisingly sensitive and sound pretty good. The portable is a good AM Dxer at nite.
Total for both less than 25.00. So by most standards not very vintage but by 2017 standards very vintage. Table set #7-4115B portable #7-2857A

Chassis GE pics added now.

https://www.flickr.com/photos/92577012@N...1360369981

Here is the Delmonico I mentioned...
https://www.flickr.com/photos/92577012@N...0376229113

Paul

Tubetalk1
#2

Hey, ANY analog radio today IS vintage.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

Don't know why, but I have always liked those Delmonico radios.  I think it must be the odd ball name and dual speakers, how does it sound Paul?

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#4

have not played it yet, a bit leary. Need to see the underside of the chassis. The fellow who owned it had put tape on the dial where his fave statios were, tried some goo gone and a razor but need to be very careful getting the gunk off.

Will let you know. 

I always liked Delmonico potatoes!

paul

Tubetalk1




Users browsing this thread:
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently no members online.

>