1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
information on rewinding philco 90/70 coils
mg34.42
Member
***
Posts: 91
Threads: 37
Joined: Dec 2013
City: Tulsa, OK
#1

12-13-2017, 08:45 PM
ok I know the info is out there I just cant find it any one can guide me to the information so I can rewind a few coils turns gauge of wire and direction I know it was on philco repair bench at one time but I don see it there anymore
Benny
Find
klondike98
Phorum Moderator
******
Posts: 5,163
Threads: 273
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#2

12-13-2017, 09:18 PM
here is some info on Chuck's repair bench site (using the wayback machine)

His new site is still under construction.
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
mg34.42
Member
***
Posts: 91
Threads: 37
Joined: Dec 2013
City: Tulsa, OK
#3

12-13-2017, 09:29 PM
thank you so much I thought I was losing my mind any idea what direction the start side should be on the 90 coil and what direction for the start side on the 70 the reason I am asking is that there is nothing left on my coil to tell what direction it is wound 
benny
(This post was last modified: 12-13-2017, 09:45 PM by mg34.42.)
Find
klondike98
Phorum Moderator
******
Posts: 5,163
Threads: 273
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#4

12-13-2017, 11:22 PM
sorry, I don't know.
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Zenith H725
David - I think I understand but what units are you discussing (Low of 1.7, high of 3.9)? Budget constraints for Ham ...EdHolland — 01:43 PM
My Philco 37-116 Restore
You're doing great. I wish I could be more involved, but my mind is right now preoccupied with the reason I am here in ...morzh — 12:21 PM
My Philco 37-116 Restore
Hope you guys are still with me. I have moved on to the alignment. I completed the IF alignment which was pretty muc...dconant — 10:47 AM
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM

[-]
Who's Online
There are currently 1041 online users. [Complete List]
» 1 Member(s) | 1040 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration