1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
philco wire wound resistor values
nitram11
New Member
*
Posts: 2
Threads: 1
Joined: Jan 2018
City: Brandon, MB
#1

01-26-2018, 09:31 PM
Where can I find resistance values for part number 4953 wire wound resistor in model 90a double 45 tubes 
thanks Martin
Find
PhilcoPhan1936
Jeff W.
******
Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro State, Province, Country: AR
#2

01-26-2018, 10:20 PM
Welcome! That's a good question. I looked through my available documentation, with no luck. Hopefully Ron or another member here has some data or documentation that will be able to help you out.
Blessings,
Jeff W.
Jonesboro, Arkansas

http://jeffsradios.weebly.com

God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,285
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#3

01-26-2018, 11:01 PM
http://www.philcoradio.com/images/phorum/schem/90a.jpg
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
nitram11
New Member
*
Posts: 2
Threads: 1
Joined: Jan 2018
City: Brandon, MB
#4

01-27-2018, 12:47 PM
Thank you for your quick reply and now we can finish the radio up
Martin
Find
klondike98
Phorum Moderator
******
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#5

01-27-2018, 01:40 PM
Welcome to the Phorum!
Icon_wave
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration