1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
38-9 Parts List needed.
philconerd
Member
***
Posts: 60
Threads: 14
Joined: Oct 2008
City: Pequot Lakes, MN
#1

04-07-2018, 03:10 PM
This week a good friend of mine dropped off a family heirloom radio found in their attic.  This is a Philco 38-9 Table Radio.
It's in very good condition for being 80 years old!  Everything is there, I don't see anything missing.  They want me to repair it and get it operating again.  This radio is about 3rd on my project list for now, and I will get working on it soon.

So what I need is a good clear copy of just the parts list because the one on Nostalgia is too fuzzy to read.  Can anyone help me?

Thanks in advance.
G.
   
Find
Nathan Slingerland
Super Moderator
******
Posts: 1,874
Threads: 212
Joined: May 2015
City: Seattle State, Province, Country: WA
#2

04-07-2018, 03:30 PM
Sure - here you go!


Attached Files
.pdf Philco Service Bulletin No. 280.pdf Size: 576.97 KB  Downloads: 653
Find
philconerd
Member
***
Posts: 60
Threads: 14
Joined: Oct 2008
City: Pequot Lakes, MN
#3

04-07-2018, 04:28 PM
Thank you Nathan.
Those are exactly the documents I needed for this radio.


I will post more as I begin the repairs in the next few weeks.
G.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM

[-]
Who's Online
There are currently 4723 online users. [Complete List]
» 2 Member(s) | 4721 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration