Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 37-610
#1

Hi,

Some time ago a relative found me a Philco bullet model 37-610 at a sale. Upon inspecting it later, I noted that it did not have the Deco inlaid lines on the front:- http://www.tuberadioland.com/philco-37-6...mainl.html

It's also missing its dial glass and part of the knob, though I do have these parts that I've found since.

I've seen very few of these without the lines & have been uncertain as to their authenticity. Now one has shown up on Ebay:-
http://cgi.ebay.com/6596526279

Is there a story here somewhere regarding this as a variation?

Paul
#2

Looked at the ebay set. It's glaringly a strip 'n slobber refinish. I don't believe that these models ever had Di-Noc (printed grain) finishes, but we have to wonder if the black stripes may have been printed on the panels. I'll have to check on mine, but I've always thought that the black stripes were inlays. I have both the '36 and the '37 sets.

Another possibility is that on early cabinets, the stripes WERE inlays, and they might have done a run of cabinets with either printed stripes or none at all. Since the original finish is gone from this cabinet, that information is lost.
#3

I think I would have to agree with Doug here. Although that decal looks as if it might be original, the bottom trim should be toned a much darker brown; and it isn't on this set.

Some years ago, someone was selling a very good reproduction of the 1932-36 PHILCO decal. I once had a few of those, and they looked just like the originals, unlike what you can get today. The decal on this set could be one of those repros, placed on an older, poor refinish, for all we know.

I looked in my copy of Furniture History, and it is silent on the stripes/no stripes issue. It only mentions that the 1937 version was available in maple as well as walnut; the vast majority (28,100) were walnut as opposed to 3,000 in maple.

I wouldn't be a bit surprised if Doug is right on the money regarding the stripes being printed later on, although I seem to recall the 1936 model did have inlaid stripes?

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM
Philco 38-7 Speaker
7K should be fine. While not a perfect match (This transformer is meant for 6V6 tubes), Antique Electronic Supply (AES)...MrFixr55 — 08:03 AM
40-150 General questions
I discovered a stamp on the underside of the breadboard on my Philco 40-150. It is"56-1417' in black ink with numbe...Kevin_D — 07:14 AM
Philco 38-7 Speaker
FYI the Impedance of the HR20 (the one I have) secondary of the audio transformer is 5 ohms. The 38-7XX speaker is suppo...tludka — 04:22 PM
Philco 38-7 Speaker
Yeah, don't use the transformer currently on the H-20 (Dopf, I thought "H20, is that new technology, a speaker usin...MrFixr55 — 03:51 PM

[-]
Who's Online
There are currently 2520 online users. [Complete List]
» 1 Member(s) | 2519 Guest(s)
Avatar

>