Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Westinghouse model 1029
#1

This is the last one I did for this summer. It is too chilly to do any refinishing  right now.
  It is a 1937 Westinghouse model 1029.   This is the third one of these I have owned.
   The grill cloth configuration is all original and quite different.
 
I recapped the chassis and it was working good  until I put it in the cabinet.
Then it would just quit. So I took it out and found there was a cold solder from a previous owner.
     Once it was fixed the radio plays very good.
 
Dan in Calgary


Attached Files Image(s)
                   

   Living in Calgary Alberta
#2

Very good-looking console. And 4 SW bands make it an upscale model.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

The grille cloth makes you think: "What's behind the curtain? "

And look at the size of that chassis. Looks like the speaker could easily be fully enclosed. Very nicely done!
#4

Speaking of the curtain: is this the only grill cloth or is there another behind it?

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#5

There is nothing behind that curtain, just a speaker board, so the someone could put a hole in the speaker,
but it has not happened on any of these that I have owned.
 My model is the 1012 Y.
     The other 1029 is a model 1029 X and here is a photo of it   I also had one of these  and the chassis is the same on both radios.


Attached Files Image(s)
   

   Living in Calgary Alberta
#6

I suspect the other was the same at some point, and the curtain is to protect the actual cloth from cats.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#7

I have found that on the radio with the curtain, every one of them was the same, and there was no modification
done to the cabinet.
 That is the way it came from the factory.

   On the model with the wood  grill work,,it comes the way you see it,from the factory
 I have had two of those also
 Dan in Calgary.

   Living in Calgary Alberta




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently 3288 online users. [Complete List]
» 1 Member(s) | 3287 Guest(s)
Avatar

>