Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

here is another one i need to id philco
#1

i was told this is a philco 38-116 but it has a different cabinet than the one i have and can i get repo speaker cloth for this 
benny


Attached Files Image(s)
       
#2

I can tell you one thing it isn't that's a 38-116 chassis or cabinet. Will shoot for 38-2.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

I think Terry is right. I have one like it that i have not looked at in along time. My 38-116 is NOT like that!
#4

Just take a look through the Philco Radio Gallery.

https://philcoradio.com/gallery2/1938a/#Model_38-2XX

Whoomp, there it is.

--
Ron Ramirez
Ferdinand IN
#5

Yes but did it have the wide chevron grille cloth?

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#6

The 38-2 used the Philco "Ribbed" pattern originally, mounted vertically (up and down). Not the chevron cloth.

--
Ron Ramirez
Ferdinand IN
#7

is anyone making repo speaker cloth
#8

Radio Daze lists their GRC14 which is not exactly like the original, but is the best you can do now.

https://www.radiodaze.com/grille-cloth-14-item-grc14/

--
Ron Ramirez
Ferdinand IN
#9

thank you Ron i have been reading about the 38-690 you have worked on these radios are more complex to work on but i am very impressed with the reception they get when finished my very first try at one of these is the philco 38-116  
benny




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM

[-]
Who's Online
There are currently 5290 online users. [Complete List]
» 2 Member(s) | 5288 Guest(s)
AvatarAvatar

>