Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

1st gen Model 84
#1

I was thinking since the weather getting better I should have some sets to refinish. One came to mind an 84 that I thought I had serviced a yr or two ago. Pulled it off the shelf and noticed that it was missing the 80 tube so found one. Gave it a go and no dice just hum. Guess I didn't service it.

Remove the chassis from the cabinet to find the 42 was missing too. Replaced the 42 and didn't help much. Spkr and ac cords were pretty tattered both original. Previously I did rebuild the filter cap, rewind the osc and ant coils. Spent about a hour and a half checking/replacing resistor and rebuilding block caps. Made a new spkr cable and replaced the line cord.

After all that was put in place I gave it a try and it awoke from it's slumber.Tuned around a bit and got Paul's station WBZ but didn't hear him on it.
The grid leak resistor is a little high at 6M so I'll probably drill out the rivets that hold the coil covers on. I think that offers more access to clean the covers, chassis, and get to the gl resistor.

And then there's the cabinet...


Attached Files Image(s)
           

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry




Users browsing this thread:
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Hi Paulo, Welcome to the Philco Phorum. I can see why you want to find good reproduction parts. That is a bea...MrFixr55 — 11:10 PM
HiFi (Chifi) tube amp build - but my own design.
Tim, I have some bakelite sockets in my work shop that I can dig up. I believe quite a few are NOS. I will take photo...RodB — 10:03 PM
Philco 610B oscillator wiring
> The cathode as noted is wired directly to the ground side of the heater filament for that tube, not to the #17 and ...Radioroslyn — 08:12 PM
HiFi (Chifi) tube amp build - but my own design.
Tim; I noticed your post a little late, but I would take one of the junk sockets and try to break a chunk out of it wi...Arran — 08:07 PM
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM

[-]
Who's Online
There are currently 1463 online users. [Complete List]
» 1 Member(s) | 1462 Guest(s)
Avatar

>