1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Refinishing Bezel
Pcorb
New Member
*
Posts: 1
Threads: 1
Joined: Sep 2022
City: Midland State, Province, Country: NC USA
#1

09-13-2022, 03:46 PM
I am in the process of restoring the cabinet bezel for a Philco 46-1209. The original finish has all flaked off down to the bare wood.      . It’s basically a clean slate, but I’m unsure how to approach a new finish. Any ideas would be greatly appreciated.
(This post was last modified: 09-13-2022, 04:24 PM by Pcorb.)
Find
klondike98
Phorum Moderator
******
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#2

09-13-2022, 04:21 PM
Welcome to the Phorum!
Icon_wave
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
Sean
Member
***
Posts: 151
Threads: 5
Joined: Oct 2005
City: Sullivan, MO
#3

09-14-2022, 09:00 AM
You might look into a self-adhesive vinyl with a wood grain on it.  I had bought some a few years ago from a company who markets it for putting wood grain on vehicle dashboards.  It can be worked around curves like those on your bezel.  I've used it on a couple radio projects.  One was to replace a photo finish burl walnut strip on an Airline cabinet and the other to cover the face plate on an Atwater Kent 480.

I believe I bought it from Metro Restyling:

https://metrorestyling.com/collections/w...vinyl-wrap
Sean
WØKPX
Find
radiorich
Phorum Expert
*****
Posts: 1,599
Threads: 101
Joined: May 2008
City: Omak State, Province, Country: WA
#4

09-14-2022, 02:22 PM
Hello Pcorb,
the link that Sean shared looks like a great idea !
Sean that is a great link I will for sure save it .

Sincerely Richard
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM

[-]
Who's Online
There are currently 3172 online users. [Complete List]
» 1 Member(s) | 3171 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration