Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

16B cabinet color
#1

The house of a recently deceased neighbor is being cleaned out and this kinda tired 16B was headed for the dumpster. I thought
I'd see what I could do with it and, with the amount of labor involved, I might as well do it right-  so here's my question: What
color were the dark parts of the cabinet, black or very dark brown? Was the finish meant to be opaque or was the grain meant
to show through? The cabinet was stripped long before I got it.
  One idle curiosity question too. I'm not used to seeing eight-sided knobs on Philco products. How long were they used and did
the whole product line get them or just some models?
   Sorry for asking questions you guys probably settled long ago.
-Dave


Attached Files Image(s)
   
#2

Hi Dave - a previous post on the colors for these cabinets: https://philcoradio.com/phorum/showthread.php?tid=8830
#3

Here's the link to our gallery photo as well:
https://philcoradio.com/gallery2/1935a/#Model_16B
#4

Hi Dave and welcome to the Phorum,

You found one of Philco's best table top sets. It's a beast! I have a couple of the them.
Here's a link to the 1st cabinet I did. https://philcoradio.com/phorum/showthread.php?tid=19986
It was stripped too. And broken. I ended up using
Mohawk Van Dyke Walnut M100-0353. I don't think it's as red as the extra dark walnut.
Also used a lot of sanding sealer. The hypo work wonders for doing the pinstriping.

I'll mention while your working on the cabinet be sure to check the joints. Loose joints
can cause splitting and cracking of the corner and top panels as it's a heavy set to pick
up by the rear arch.

As for the knobs I can't think of many sets that use them. Would have been around 1934
-35. Renovated Radios was making repos for all 3 of them.  And the grille cloth can be had
from Micheal Katz.

GL w/your new project!

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#5

Hello Dave and welcome to the Phorum! Terry wasn't kidding when he said "beast". Make sure the table you put it on is sturdy as well! The others showed you where to start, so I'll just say Good Luck! Take care and BE HEALTHY! Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan




Users browsing this thread:
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently no members online.

>