Jackson Bell model 68 Tulip
Posts: 85
Threads: 9
Joined: Nov 2005
City: St. Petersburg, Fl.
Didn't know where else to go here.
I need help. I need a paper schematic, a good picture of original knobs, and, a rebuildable speaker for this set. It uses a Magnavox model 138 8" speaker. What can anyone tell me about this set, and, can anyone help me get parts for it?
I really want to restore it.
What year was this set made, and, what is the quality of this 8 tube radio?
I had replaced fried power transformer in it years ago, re capped it, and, put a temporary spkr. on it.
It would only play one station very weakly when I put my hand on secondary coil of first RF. And, that, same station all the way accross the dial.
What could be wrong?
Thanks.
Bill Cahill
"If it lights in the dark and leaves you with a warm glow it's tubes."
"Honey, did you warm the baby bottle on my 75 watt hi-fi again?"
"I left it somewhere, but, where?"
Posts: 190
Threads: 8
Joined: Oct 2005
City: Lexington, SC
Schematic emailed.
Hearing only one station generally means the local oscillator is not running. A strong nearby station is able to force its way in enough to be heard. Richard
Posts: 292
Threads: 17
Joined: Aug 2010
City: Yorkville IL
I'll post this link, I'm sure you've already looked there, but it does show the knobs.
http://www.radiomuseum.org/r/jackson_be_68_2.
Glenn
Happily back in Illinois..not.
Posts: 85
Threads: 9
Joined: Nov 2005
City: St. Petersburg, Fl.
Please forgive my lack of knowledge. I am familiar with I F circuits, but, Haven't had enough experience on RF sets. Didn't know they used an oscilator on rf sets.
Thanks.
Got e mail, and, schematic. Many thanks.
Bill Cahill
"If it lights in the dark and leaves you with a warm glow it's tubes."
"Honey, did you warm the baby bottle on my 75 watt hi-fi again?"
"I left it somewhere, but, where?"
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
There is no local oscillator in this set. It's a TRF, not a superheterodyne.
I have no idea when it was made, but it seems to be nicer than a lot of TRF sets of the late twenties/very early thirties...three stages of RF amplification, and push-pull 45 outputs.
I don't see much in the way of components between RF stages. RF coils, the 0.25 uF cathode bypass cap that is common to all of the RF amplifier tubes, resistors in the front end and voltage divider network, tubes...any of these could be causing the problem. Also a bad field coil, or filter choke. Check the voltages. You are lucky in that Rider's gives the voltages. A lot of the schematics for smaller companies such as Jackson-Bell didn't even give component values, let alone socket voltages.
--
Ron Ramirez
Ferdinand IN
Posts: 85
Threads: 9
Joined: Nov 2005
City: St. Petersburg, Fl.
Actually, it's 4 rf stages. The radio dates to 1931.
It was a well made set. I'm missing the spkr. Made some jury rigs to try set.
Bill Cahill
"If it lights in the dark and leaves you with a warm glow it's tubes."
"Honey, did you warm the baby bottle on my 75 watt hi-fi again?"
"I left it somewhere, but, where?"
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
No, Bill, it has three RF amplifier stages. The fourth "stage" is the detector circuit.
--
Ron Ramirez
Ferdinand IN
Posts: 85
Threads: 9
Joined: Nov 2005
City: St. Petersburg, Fl.
Thanks, Ron. I thought this one had a seperate detector. On the 1928 Edisons with 3 rf tubes, they used part of the 27 as the detector.
I have to familiarize myself with this schematic.
Oh, by the way. One of the big 3 knob dealers contacted me the other day. She offered me a set of bakelite knobs she says are for my set. The only difference is the picture of another set I saw shows a 3 step knob, and, these are two steps. Otherwise, they look exactly like them. Any comments here?
My friend, Mr. Detrola from ARF says since he's seen variations of original knobs on different sets produced by this companny, that it's very plausable, in his view, that these are yet another variation.
Bill Cahill
"If it lights in the dark and leaves you with a warm glow it's tubes."
"Honey, did you warm the baby bottle on my 75 watt hi-fi again?"
"I left it somewhere, but, where?"
Users browsing this thread:
|
Recent Posts
|
Philco 91 Speaker Replacement
|
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM |
Restoring Philco 37-604C
|
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one.
Which does not m...morzh — 01:44 PM |
Philco 38-2 Automatic Tuning
|
When you push the lever, you are supposed to rotate the disk to the desired station.
Then the magnetic tuning will acqu...morzh — 01:42 PM |
Philco 38-2 Automatic Tuning
|
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM |
Philco 91 Speaker Replacement
|
How would I go about removing the spider from the cone?dconant — 12:04 PM |
Philco 38-2 Automatic Tuning
|
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM |
Does anyone make photofinish replacements?
|
Here’s the link to the DIY photofinish section of our site:
klondike98 — 09:46 AM |
Delco car radio Peko vibrator converstion issues
|
Hi Richard,
Thx for posting the schematic. As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM |
Delco car radio Peko vibrator converstion issues
|
hello mr Fixr,
The Electro Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM |
Delco car radio Peko vibrator converstion issues
|
How about putting a choke in the power supply?
The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM |
Who's Online
|
There are currently no members online. |
|
|