Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

What is this??? need an id....
#1

can someone help id this?...........thnx

http://flint.craigslist.org/atq/2495624159.html
#2

It isn't a Philco, so moved this topic to the appropriate section.

Sorry, I don't know what it is either...but I know what it isn't... Icon_wink

--
Ron Ramirez
Ferdinand IN
#3

Erg, that emblem under the dial looks very familiar. I almost want to say it's an early Wards Airline radio set, but I'm not totally sure. It is a nice complete looking unit for the price though. The tag is intact on the back, but the picture is too small!

No matter where you go, there you are.
#4

I'm just like Jayce, I've seen that emblem but I just seem to place it. I was thinking maybe a Knight but I too a quick look and didn't see it. Maybe a Lafayette? I don't know.
Sorry OM
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#5

Looks like an Amrad logo to me, and the radio looks very similar to the Symphony that was part of their Bel Canto series from ~1929 or 30. Amrad went belly-up in 1930 so this may be one of their last sets.

http://www.radioatticarchives.com/radio.htm?radio=8620

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#6

You nailed it, Eliot!




Users browsing this thread:
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently 4107 online users. [Complete List]
» 2 Member(s) | 4105 Guest(s)
AvatarAvatar

>