Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

volume control
#1

Can someone tell me the resistance of a philco 7439 volume control.
#2

If it is for the model 80 it's 20K. Two quick checks, one unplug set turn volume all the way up. Measure resistance from ANT post to chassis ground. Should be very low like a few ohms. If not antenna coil primary is open. Two, Turn volume all the away down.Measure resistance from antenna post to chassis ground. Should read about 20,000 ohms. If not check volume control, open or bad ground connection.
How's your oscillator doing?
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

What model Philco are you working on?

I didn't see any data on your part number on Philcorepairbench.com.

-Keith
#4

Terry is correct, it is 20K. Part no. 7439 was used in model 80 and the three-knob 81.

--
Ron Ramirez
Ferdinand IN
#5

Do I get a prize????
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#6

Yeah - a Philco 84B that needs complete restoration. Icon_twisted Icon_lol

--
Ron Ramirez
Ferdinand IN
#7

I unsoldered one outer lug, not the one to ground and measured it like a resistor, 17 ohms.
Strange, then I unsoldered the center lug and it read 27k. I thought you can measure a pot like a resistor if one of the outer lugs is disconnected.
#8

Depending on the circuit this may not be true, IE this case. However if the wiper is all the way toward the still connected end you should be able to get an accurate reading. Then you could connect the ohmmeter between the center and unconnected end and sweep it, and you will then see if there are any open spots.
#9

It also maybe effected by the very low resistance of the antenna coil connected to the wiper and ground.
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry




Users browsing this thread:
[-]
Recent Posts
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM
Part numbers to model cross
Jim, We have this index put together by Dale Cook but I don't think that is quite what you are looking for. The Parts...klondike98 — 09:37 PM
Philco Model 38-7: what caps & resistors do fail typically?
Yep the dim bulb test is OK but I'd definitely replace all those electrolytics before I did it. Since those #47 conden...klondike98 — 09:18 PM
Philco 42-345 Restoration/Repair
The resistor is a 2.2 Meg, it was the last one I hadn't replaced. The broadcast is coming in after replacing it.osanders0311 — 09:09 PM
Philco 42-345 Restoration/Repair
What does the resistor measure? I think it should be 3.3 Meg. If the oscillator coil has continuity and the resistanc...RodB — 09:03 PM
Philco Model 38-7: what caps & resistors do fail typically?
Good idea to check the coils... then I'll get hold of an incadescent light bulb and see what happens when the unit is sw...Musaeum — 08:49 PM
Philco 42-345 Restoration/Repair
I have that same set, ain't too much shortwave I like anyway.....it is a good AM DX set. PaulPaul Philco322 — 08:32 PM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum, Martin! Open a new thread in Philco Electronic Restoration when you begin working on your 38-7. ...GarySP — 08:28 PM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum! :wave: Here's the schematic for that radio from our digital library: Something to do bef...klondike98 — 08:05 PM

[-]
Who's Online
There are currently no members online.

>