Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Picked up this Arvin console today !
#1

woods bad but the rest looks good Anyone have anything like this one?
[Image: http://i1095.photobucket.com/albums/i474...9811ec.jpg]
[Image: http://i1095.photobucket.com/albums/i474...to0104.jpg]
#2

Now that's neat! I'll have to show Debbie this thread...she is partial to Arvin sets.

--
Ron Ramirez
Ferdinand IN
#3

Nice Arvin console indeed!! Great find fixinmyphilco! Enjoy restoring that set, it should sound really good after full electronics restoration!

@ Ron, my wife is also fond of the old Arvin & Truetone sets. We have many restored Arvin (Noblitt Sparks) metal midgets sets here my sweet wife brought in from her finds at antique stores, etc. over many years past. She loves the little metal sets indeed. We have all the early 2-tube metal midgets through the 4 tube sets made by Arvin, Mighty Mite, Kent, etc. that Noblitt Sparks built Radios for. These old rare metal midgets sets are in many different colors, and were at one time punch card giveaways at carnivals etc, as advertising items. Back when you could win something good at the State Fair or Carnival besides stuffed bears or cheap toys. Icon_thumbup
#4

Nice radio! I like Arvin's stuff as well, especially some of the consoles they made. Sadly, they don't seem to exist around here and I mostly find thier 50's table radio offerings. Didn't they make radios for Sears for a while as well?

No matter where you go, there you are.
#5

Hello Jayce, Yes, Noblitt Sparks Industries in Indiana who made the Arvin sets also produced sets for several other manufacturers, especially the small metal midgets radios, 2, 3, & 4 tube sets. They also made the metal midgets Silvertones sets for Sears. They also made car heaters for the old cars & trucks back in those days as well as many other items and appliances.
#6

Nice find. No Arvins here eiither, at least under my roof! Jay, you never know what you may find just around the corner.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently no members online.

>