1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 60 Hum problem
Guest
Unregistered
 
#1

04-13-2007, 08:22 PM
I recapped this Philco awhile back. Sounded fine, but now it has developed an AC hum and lost all reception. I have by-passed and checked both filters and they are fine. If I put my probes on the 42's K and P, no scratching in the speaker. Any suggestions? Also, my Riders says with Run# 7 resistor #19, part # 4518 (5,000 ohm) should be changed to a 99,000 ohm. My schematic shows that resistor #19 is a 51,000 ohm. Any help there as well.
Thanks in advance.
Bill
Guest
Unregistered
 
#2

07-28-2007, 02:22 PM
Bill,
This may be a bit too late, but if you still have the hum issue, did you replace the line filter caps? They are a block cap at the bottom near the wirewound resistor with the power cord attached. This should be rebuilt with (2) .01 or .015 caps instead of leaving the old paper ones in. An article on philcorepairbench.com state something about this. Of course, if you look at my new posts re: this radio, you will see that I'm having my troubles too! Best of luck. Ron M.
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A5...MrFixr55 — 06:48 AM

[-]
Who's Online
There are currently 5224 online users. [Complete List]
» 4 Member(s) | 5220 Guest(s)
AvatarAvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration