1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
How to deal with blush
Art Hoch
Senior Member
****
Posts: 403
Threads: 40
Joined: Feb 2011
City: McPherson, KS
#1

05-29-2013, 01:59 PM
Well, I should have known it was too humid to spray finish coat lacquer on today and now I have some blush to take care of. It's on the final step after I toned the "cheap" wood with Mohawk toner to darken it. What do you say I should do now? I don't want to have to sand and then retone several small areas including the grille bars on my Philco 38-1 console.
Find
Phlogiston
Radio-Fixer-Upper
*****
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
#2

05-29-2013, 02:05 PM
First of all wait for a day and see if it goes away.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Website Find
Art Hoch
Senior Member
****
Posts: 403
Threads: 40
Joined: Feb 2011
City: McPherson, KS
#3

05-29-2013, 04:03 PM
Sounds good to me. I'm in no special hurry.... I've had to wait to get started on this cabinet since mid-February!!!
Find
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#4

05-29-2013, 06:46 PM
Mohawk No Blush Plus will make that blushing disappear like magic.

[Image: http://woodfinisherssource.com/cart/imag...3-0475.jpg]

Great to have if you spray any lacquer anytime the weather is humid.
--
Ron Ramirez
Ferdinand IN
Find
TA Forbes
Deviate Emeritus
*****
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
#5

05-29-2013, 06:50 PM
Going over it lightly with 0000 steel wool will remove it.

In NC I encounter this often.
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
The string is held tight with springs. I use black 20 pound test nylon fishing line (plentiful here in MN). Take picture...RodB — 07:15 PM
Philco 42-345 Restoration/Repair
Thank you very much for your help and sending the pictures, the cables must have been wrapped very tight around the spin...osanders0311 — 06:52 PM
Philco 42-345 Restoration/Repair
As you can see, mine has a chunk of hard rubber remnant on the shaft next to the chassis. I would say the shaft was, at ...RodB — 06:13 PM
VTVM meter moves when my hand is next to it & not on
It's  okay because my wife hoards yarn, so one more piece of radio rest equipment is ok tooBruce B — 05:56 PM
Philco 42-345 Restoration/Repair
I think my 42-340 is the same as your 345 without the buttons. Give me a few minutes and I'll pull the chassis and I'll ...RodB — 05:43 PM
VTVM meter moves when my hand is next to it & not on
Can't turn that deal down.RodB — 05:23 PM
VTVM meter moves when my hand is next to it & not on
Thanks Bob, I was kinda figuring on that, but I have never seen anything like this guy does.  It's inability to come ba...Bruce B — 04:59 PM
Philco 42-345 Restoration/Repair
I have attached a markup of the channel selector cable upper right in the picture under the chassis, this cable is broke...osanders0311 — 04:40 PM
VTVM meter moves when my hand is next to it & not on
That's static electricity. Take a used fabric softener dryer sheet and wipe the dial cover then discharge your body to t...RodB — 04:39 PM
Philco 42-345 Restoration/Repair
Not for certain if this will be a full restoration or repair, but after opening the unit up I would rather clean and fix...osanders0311 — 04:31 PM

[-]
Who's Online
There are currently 1792 online users. [Complete List]
» 2 Member(s) | 1790 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration