Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Restore a 37-610
#1

Hello all! I just wanted to firstly state that I am very new to radio restoration and want to say thank you in advance to any and all help that I receive. With that said, I have come into possession of a Philco 37-610 radio. At least that is what the the sticker on the inside of the cabinet claims. It appears to be a 37-623J cabinet, however. Anyways, I came into possession of this after my grandfather had passed. I would ultimately like to at least restore the cabinet for my grandmother as a gift. I believe that the electronic aspect may be a bit past me as it appears the components are in pretty poor shape.
Where could I find the knobs for this cabinet and a new grill cloth? Also, what's the best way to clean the dial (I know thats not the term, very new)? Again, thanks in advance and I am very excited to start learning about this new hobby!
#2

Are you near any of the meets? There is one this weekend in Huntington West Virginia where you cand find knobs and parts also those knobs are reproduced look on tubes and Moore.com and like sites. As for the dial there was a post on here that said mineral spirits will clean the dial without removing the numbers. Good luck finding grill cloth, reproductions have dried up.
#3

check out this site.I just found it myself! I hope it helps. http://web.archive.org/web/2005110310030...index.html
#4

Grillecloth.com (Radio Grille Cloth Headquarters) is out of business.

--
Ron Ramirez
Ferdinand IN
#5

A good place to start for finding knobs is the page on PhilcoRadio: http://www.philcoradio.com/resourceb.htm#l .
#6

Thanks for the advice guys! I think I will just plug away and try to find some knobs on the site Bob provided while periodically checking out eBay and Craigslist.
Is there anyway to find a list of where these meets are that Tab suggested I look into?
Also, I found this grill cloth on RadioDaze http://www.radiodaze.com/product/12906.aspx - is that the right one?
#7

Yes that's it I'm glad to see someone is selling at least some cloth. Todd




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Not sure if anyone has tried this but there are 6.3 volt miniature lamps in bayonet and screw-in base options available ...GarySP — 11:31 AM
Shadow Meter Bulb
Any 6.3 volt pilot light will work. I would use the brightest one I could find in my workroom. Be sure the dial is clean...RodB — 10:45 AM
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM

[-]
Who's Online
There are currently 7780 online users. [Complete List]
» 1 Member(s) | 7779 Guest(s)
Avatar

>