Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

#16

hey guys
before gets too ugly here
we all have opinions to who we like, some are better then others, we try different people if not better then we stick with who we are satisfied with. Service and Delivery..
back to original question was if 7b7 was same as 7r7 as they look same and some one put them in radio which was cover in dust ,I recapped and replaced some wires turned on all tubes lite but that one and had no sound and being new I didn`t know
sam8)
#17

It isn't going to get ugly, I won't let it...remember, I own the joint. Icon_smile

Eric - didn't mean to be argumentative, and as Sam said, it all boils down to which vendor you prefer. My point is that a lot of guys in the hobby who supply parts and services have other things going on and can not always provide instant service.

Oh, by the way, Marty - yes, Jim Cross is one of the good guys. Icon_thumbup

--
Ron Ramirez
Ferdinand IN
#18

Are we definitely speaking of the same Bob?

My experiences have been excellent with him.

RE: tube substitution, there is a time and a place for it. Personally, I recommend them (Guides) if for nothing else than expanding one's knowledge.

And while there are definitely cases where the substitution of a tube can introduce different parameters, there are (my opinion) just as many in which the tube will function in an acceptable manner.

Many subs are not "either, or." Example: you can use a 5R4 in place of a 5Y3, BUT you cannot use a 5Y3 in place of a 5R4. Not that I would waste a 5R4 where a 5Y3 belongs, BUT if I was out of 5Y3s and had a 5R4 sitting in the stash, I would certainly use it until another 5Y3 came along.

In some radios the Manufacturer listed different types of tubes that could be used. Example: The Truetone D-697 on the schematic lists either a 6U7G or 6K7 tube for the RF and IF amp tubes. Another WG set does the same for the rectifier (5Z4 or 5Y3).
#19

+1 TA Icon_thumbup

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

#20

I've subbed out tubes a couple of times in the past. It kept me going until the correct tube arrived in the mail. Otherwise, the project would just sit there gathering dust. Tube sub guides are handy if you don't have a gigantic tube stash.

The artist formerly known as Puhpow! 8)




Users browsing this thread: 10 Guest(s)
[-]
Recent Posts
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM
Philco 42-1008 conversion kit
I read about a kit to convert the variable speed changer in the Philco 42-1008 into a single speed unit.  That would rem...alangard — 09:30 PM

[-]
Who's Online
There are currently 6149 online users. [Complete List]
» 1 Member(s) | 6148 Guest(s)
Avatar

>