Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

help with Philco phonograph
#1

Hey everyone. I'm sorry if I'm posting this in the wrong section. But I have been looking everywhere online and I cannot find anything on my Philco. I hope someone can help. I would love to restore it. I have attached some pics.

[Image: http://i1125.photobucket.com/albums/l583...sfggqi.jpg]

[Image: http://i1125.photobucket.com/albums/l583...phecep.jpg]

[Image: http://i1125.photobucket.com/albums/l583...xnga1i.jpg]

[Image: http://i1125.photobucket.com/albums/l583...k1hf9d.jpg]
#2

Anyone?
#3

Try to place it in Philco Electronic restoration first, but if no one answered it might be due top the fact no one has anything on it.
You did not list the model; I tried C5-1555 and found nothing.
#4

Hi Shane:
I don't have any info on your phono but a safe bet is it needs a new cartridge and the electrolytic caps inside replaced at the very least. Do you have any kind of electronics knowledge? What are the faults at the moment?

Gregb
#5

No faults just wanting a new needle and to restore the case. And to find any sort of info on it that I can.
#6

You might try connecting with the folks at this web site: http://www.everythingradio.com/NeedlesandCartridges.htm although I have no experience with them. Does your needle/cartridge have any numbers or info on it? If so, that may help identify what you need. Folks on this Phorum have had good luck with West Tech http://www.west-techservices.com/p1.htm in rebuilding cartridges, but the ones I'm thinking of have been older models than yours.
#7

Ok thank you!




Users browsing this thread:
[-]
Recent Posts
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM

[-]
Who's Online
There are currently 2742 online users. [Complete List]
» 3 Member(s) | 2739 Guest(s)
AvatarAvatarAvatar

>