1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 16B noise suppression circuit pot
fields 100
Member
***
Posts: 228
Threads: 64
Joined: Dec 2013
City: Northbrook, IL
#1

08-16-2014, 05:44 PM
Does anyone know off hand the wattage of the #82 pot? It is 10K,it's bad and I have not powered the set yet to calculate it.

http://www.nostalgiaair.org/PagesByModel...013139.pdf
(This post was last modified: 08-16-2014, 05:45 PM by fields 100.)
Find
Mondial
Phorum Expert
*****
Posts: 1,114
Threads: 14
Joined: Feb 2013
City: Irvington, NY
#2

08-16-2014, 06:44 PM
Look like the original is probably a 2 Watt wirewound?

Under normal operation, the pot dissipates only 0.16 Watt, but at turn on its quite a bit more. Before all the tubes heat up, there is almost 500 V across the voltage divider, and the pot is subject to about 100 V. Calculating the power (100 x 100 / 10000 ), it is 1 Watt under those conditions, so to be conservative I would go with a 2 Watt replacement
(This post was last modified: 08-16-2014, 06:45 PM by Mondial.)
Find
fields 100
Member
***
Posts: 228
Threads: 64
Joined: Dec 2013
City: Northbrook, IL
#3

08-16-2014, 07:10 PM
That 's great. I have already ordered 5W, but was not sure. The original is wire wound. The new one will fit nicely.
Thanks.
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread:
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently 2348 online users. [Complete List]
» 1 Member(s) | 2347 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration