1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
38-2670 cabinet problem
thirtiesradio
Senior Member
****
Posts: 344
Threads: 38
Joined: Jun 2011
City: Tustin State, Province, Country: California
#16

10-09-2014, 12:38 AM
You can install veneer on a sharp radius horizontally by soaking it in veneer softener and using the cabinet as a form. Once dry you can trim and install it. They used steam in the old days......some cabinet makers still do although most use bending irons, heat blankets and vacuum forms. I'm sure there are other ways as well.
(This post was last modified: 10-09-2014, 12:49 AM by thirtiesradio.)
Find
murf
Senior Member
****
Posts: 668
Threads: 144
Joined: Jun 2011
City: Elko,MN.
#17

10-26-2014, 03:01 PM
Ok,
Here is the finished cabinet guy's.[Image: http://i1161.photobucket.com/albums/q509...abinet.jpg]
Find
sam
Phorum Expert
*****
Posts: 2,572
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
#18

10-26-2014, 03:29 PM
looks great murf Icon_clap
Find
Eliot Ness
Phorum Expert
*****
Posts: 3,135
Threads: 54
Joined: Apr 2011
City: Lexington, KY
#19

10-26-2014, 03:36 PM
That turned out very nice Icon_thumbup
John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
Find
klondike98
Phorum Moderator
******
Posts: 5,084
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#20

10-26-2014, 03:46 PM
Great save murf!!!  Looks great  Icon_clap Icon_clap Icon_clap
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
thirtiesradio
Senior Member
****
Posts: 344
Threads: 38
Joined: Jun 2011
City: Tustin State, Province, Country: California
#21

10-26-2014, 10:16 PM
Very nice!
Find
jerryhawthorne
Phorum Expert
*****
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
#22

10-27-2014, 02:12 PM
Murf, what a great job. Congrats
Jerry
A friend in need is a pest!  Bill Slee ca 1970.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5476 online users. [Complete List]
» 1 Member(s) | 5475 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration