Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

need help Model 19 code 126
#1

Hi all. I have a model 19 code 126. Need to find a clear schematic for it. I can pull up the basic 19 and the code 128 from N/A but not this one. It seems to be different than these two however most like the original 19. Problem is with that one I can't make out the part numbers on it. Anyone have a clear one? Icon_crazy

Happiness is a warm glowing radio!
#2

(06-20-2015, 03:14 PM)earlyradios Wrote:  Hi all. I have a model 19 code 126. Need to find a clear schematic for it.  I can pull up the basic 19 and the code 128 from N/A but not this one.  It seems to be different than these two however most like the original 19. Problem is with that one I can't make out the part numbers on it. Anyone have a clear one?  Icon_crazy

Order one from Chuck Schwark. Inexpensive and you will have a good quality document.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

While you're waiting for the service package from Chuck...

Take a look at this page on my site. It goes into great detail on the various differences in the model 19 during its production, with several different schematics:

http://www.philcoradio.com/tech/19evol.htm

--
Ron Ramirez
Ferdinand IN
#4

I suppose you've looked at these: http://www.philcoradio.com/tech/19evol.htm
I think I've got a code 126 0r 7 in the chairside with separate spkr.

Which one do you have??

Terry
#5

All good stuff! Thanks. Ron your site is awesome. I should have looked before...

Happiness is a warm glowing radio!
#6

I just printed all of Ron's and stuffed them in the Riders manual. Sometimes it is mix and match.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM

[-]
Who's Online
There are currently 5061 online users. [Complete List]
» 3 Member(s) | 5058 Guest(s)
AvatarAvatarAvatar

>