Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

38-116 off Craigslist
#16

[Image: http://i1319.photobucket.com/albums/t679...y9a9al.jpg]


[Image: http://i1319.photobucket.com/albums/t679...w9hvrg.jpg]

Nearly done with the cabinet. Few more details to finish up. Grill cloth on the two smaller speaker outlets nearly drove over the edge. Looks slightly different depending the angle you see it from. Finally chose one set up, and left it. Waiting on the capacitors to be delivered so I can start on the re-cap. 
#17

Very nice looking. Great job. Good luck with the chassis restore.
#18

Did the 38-116 have a back cover?? I know that some of the older higher end sets had a cover over the spkr section for acoustic. Even with some vent hole at the top for the electronics would think it would get hot in there.

Terry
#19

Just wanted to add, finished the re-cap and it's playing great. I see what all the hype is about. This thing sounds great and the volume, without distortion, is incredible. A new favorite. 
#20

Nice job refinishing the cabinet. We all knew you had it in you! Looks great!
#21

Looks fantastic!

 I just got one and the ONLY good thing about it, is that the finish is already 99% stripped.

Me


Attached Files Image(s)
   

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#22

Kirk where did you find yours?
#23

I got them from Oyster bay Long Island


Kirk

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#24

Kirk,
 Them? How many did you get?
                            Henry




Users browsing this thread:
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently 2346 online users. [Complete List]
» 1 Member(s) | 2345 Guest(s)
Avatar

>