Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

39-17 Grille cloth supplier?
#1

Who has the most correct grille cloth for my 39-17 cabinet that Fred just finished for me?  What item number or name is it?  Thanks, Steve
[Image: http://www.surfacezero.com/g503/data/500...170350.JPG]
#2

Looking at the Gallery photo of a 39-17 I was all set to suggest Radio Daze as a supplier but I no longer see the cloth on their web site that I was looking for ( I used it in a 39-25 I did and I'm 99% sure I got it from Radio Daze). Short of that I'd look at ebay and the folks that Ron lists on the Resources Page ....and there's always a trip to Joanne Fabrics where I've found a few items.
#3

The original cloth was known as Philco "Ribbed" cloth. Bob ( klondike98 ) is correct, Radio Daze no longer carries this cloth.

I did find someone on the auction site who is selling cloth that is similar, and he says he is running out...

http://www.ebay.com/itm/300719399017

--
Ron Ramirez
Ferdinand IN
#4

Thanks guys. I'll place an order with him.
#5

Bret Menassa (think I spelled it right) is a good egg, he may have bought up the suplly when the Grille Cloth folks closed up. I am sure he gives a square deal. btw --Super Job by Fred!

Paul

Tubetalk1
#6

Paul,
Thanks for the heads-up. He's the one selling the cloth on eBay. Same number Ron mentioned. I emailed him and it's him. I think I'll get a couple extra, in case he stops selling it.....
Steve
#7

hey guys
this pattern  would be same for 250 and all bullet radios ?

sam

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#8

Same for any Philco using the "Ribbed" cloth which includes several 1936-1939 models.

--
Ron Ramirez
Ferdinand IN
#9

Looks like RadioDaze has the ribbed cloth back in their lineup....
http://www.radiodaze.com/grille-cloth-14-item-grc14/




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4809 online users. [Complete List]
» 2 Member(s) | 4807 Guest(s)
AvatarAvatar

>