Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

1930 model 96
#1

I normally don't venture into local antique shops but did so today with my dad, who knows the owner. He has this 1930 Philco high boy that is being used as a daily driver. He plays it all day every day he's open. It sounds good so at minimum the electrolyitics have been replaced. He needs space and offered it to me for  $70. The cabinet has a lot of scratches and probably needs refinishing. I certainly don't need another console but this seems like a good deal. What do you guys think? 

Greg V.
West Bend, WI
Member WARCI.org
#2

   

Greg V.
West Bend, WI
Member WARCI.org
#3

 I like the style of the cabinet. Based on some google pics of the 96 looks like that is the original grill cloth and in good condition. Depends on how much you want it as to price to pay.
#4

Greg, I bet that that 96 is unrestored and playing on all its original parts. As far as I recall, the 96 has no electrolytics, but uses a paper capacitor block for filters.

Actually I would not be surprised if it has been playing as is every day in the store . I have a 
Philco 77 which is unrestored and totally original, right down to the Philco globe tubes. I don't use it much, but it still plays great when I power it up
#5

It is a good deal.
I have this very radio I have yet to restore.
It is a good looking and one of the few with that leaves pattern.
For 70 bucks it is a good deal. Not super, not stellar, just good.
In case you want it.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#6

It's possible it was untouched...there was so much junk...er, I mean priceless antiques... around and on it I couldn't get a look at the back. If those were the original filters they were still doing a great job after 86 years....there was no hum at all! I even turned the volume down to check. I will give it some thought....and see how much I sell (or buy...) at the WARCI meet next Sunday.

Greg V.
West Bend, WI
Member WARCI.org




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM

[-]
Who's Online
There are currently 4712 online users. [Complete List]
» 2 Member(s) | 4710 Guest(s)
AvatarAvatar

>