Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 21
#1

So, here are some pictures.....
   
I need one small knob
   
The front is bowed out a little
   
Here's the underside
   
will post more of the backside when I get the chance...
#2

If you want to replace any of the cabinet parts like the baseboard or front panel give Steve Davis a holler. Does great work and prices are reasonable. Mine needed a front panel, baseboard, rear arch, and base trim.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

Here's some more, of the back; uncleaned as found condition of course...
Wonder what that hole is for on the top arch?
   
notice that shim (on right side only) holding the chassis up?
the shaft holes in the front are not centered, wondering whats going on!
   
   
lots of tree leaves and junk
the 3 tubes left to right are 45, 80, and UX-245
   
   
#4

I'd have a look at this instead of the Rider's:  https://philcoradio.com/library/index.ph...-model-21/  It's more accurate and comprehensive.

GL

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#5

Congratulations!  Finding a model 21 is almost like winning the lottery.  They had a very short production time, giving way to the 70 and 90 models.  Worthy of restoration regardless of the "found" condition.  Take care, Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
#6

(04-18-2019, 04:13 PM)Radioroslyn Wrote:  I'd have a look at this instead of the Rider's:  https://philcoradio.com/library/index.ph...-model-21/  It's more accurate and comprehensive.

GL

thanks, I will!  haven't fully explored this site yet!
#7

(04-19-2019, 10:50 AM)GarySP Wrote:  Congratulations!  Finding a model 21 is almost like winning the lottery.  They had a very short production time, giving way to the 70 and 90 models.  Worthy of restoration regardless of the "found" condition.  Take care, Gary

Yes!  you know what they say; even a blind squirrel....finds a nut once in a while!  I intend to restore carefully, and not overdo it...my son will do the cabinet work, and I will stumble through the electrics....
#8

The 21 is more or less the 20 that looks like the 70.
More so, the early run used the 20 chassis.
So most of its value is in is rarity rather than the performance or the looks.

I wouldn't mind having one to enhance the early Philco models line I have. But I know exactly how it's going to sound. Icon_smile Cause I got the rest of them.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.




Users browsing this thread:
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently no members online.

>