Thread Rating:
  • 1 Vote(s) - 3 Average
  • 1
  • 2
  • 3
  • 4
  • 5

SOS for ID; wanting to rebuild
#1

Dear Phorum

re the attached photo's: I was wondering if anyone might be able to provide some information on the unknown brand/ model number highboy consul radio.  I'm presuming it is a Philco; I really would like to identify it.

It appears to be 1920's.  It unfortunately has the chasis electronics workings ripped out including any identifing stickers, and has been used as a cupboard.  The front doors slide apart but not out or in, and the entire lid tilts right up (I don't know why).

I thought it might be for a radio-phonograph, but not likely.

I wanted to see if it would be possible to find the original radio innards/or replicate and restore it again.

Kind regards - Richard


Attached Files
.zip IMG_4629.jpg.zip Size: 1,017.29 KB  Downloads: 129
.zip IMG_4627 (1).jpg.zip Size: 1.42 MB  Downloads: 136
.zip IMG_4626 (1).jpg.zip Size: 1.48 MB  Downloads: 263
#2

Welcome to the Phorum!
Icon_wave
I've reposted your pictures so folks can see them directly:

[Image: https://dl.dropboxusercontent.com/u/5462...G_4629.jpg]
[Image: https://dl.dropboxusercontent.com/u/5462...G_4627.jpg]
[Image: https://dl.dropboxusercontent.com/u/5462...G_4626.jpg]
#3

thanks bob was getting to it
not a philco  unless export model
looks to be a westinhouse 
better pics would be great and the back side too

sam

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2




Users browsing this thread:
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently 3979 online users. [Complete List]
» 3 Member(s) | 3976 Guest(s)
AvatarAvatarAvatar

>