Philco 39-45 Push Buttons
Posts: 298
Threads: 22
Joined: May 2012
City: Chattanooga
State, Province, Country: TN
I pulled the chassis out of the cabinet this morning to clean and lubricate the push button deck and found something that made me pretty happy. The preset station coil that I thought was missing, isn't. Someone had "adjusted" the slug all the way in until it fell out the front end.  (herp derp) It was just a matter of fitting it back into the coil and reversing the screw until it was returned to its proper place. Now I have all 8 preset stations.
While I had it out, I went ahead and replaced the formerly rubber-insulated wires on the preset assembly. I'm also going to touch up the dial glass paint before everything goes back in.
It's not how bad you mess up, it's how well you can recover.
(This post was last modified: 08-31-2013, 12:48 PM by Eric T.)
Posts: 18
Threads: 3
Joined: Nov 2014
City: Groveland MA
I know this thread is a bit old, just wondering if the OP found a solution for the loose buttons?
I have the same problem, and also believe that I have installed them correctly.
There are a couple of photos here; http://antiqueradios.com/forums/viewtopi...6&t=301602
Thanks
Russ
Posts: 298
Threads: 22
Joined: May 2012
City: Chattanooga
State, Province, Country: TN
Sorry about getting back so late on this.
To answer your question:
The solution was to just quit worrying about it.
They wiggle. Meh.
Thanks for the link to your pics. They confirm the position I thought they were supposed to be in.
It's not how bad you mess up, it's how well you can recover.
Posts: 4,435
Threads: 419
Joined: Jun 2011
City: Boston
State, Province, Country: Massachusetts
I think it looks pretty good, I like the angles, very 40's to me. Enjoy.
Paul
Tubetalk1
Posts: 298
Threads: 22
Joined: May 2012
City: Chattanooga
State, Province, Country: TN
These buttons would have looked really spiffy had they been back lit.
Philco missed out on a chance to jazz up this set.
It's not how bad you mess up, it's how well you can recover.
Posts: 4,875
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
(08-26-2016, 11:56 AM)Eric T Wrote: These buttons would have looked really spiffy had they been back lit.
Philco missed out on a chance to jazz up this set.
Well, one could always rig up a warm white LED behind the pushbuttons running off the 6.3 volt filament winding, something easily removable, and which would not add too much extra of current load to the winding.
Regards
Arran
Posts: 298
Threads: 22
Joined: May 2012
City: Chattanooga
State, Province, Country: TN
(08-27-2016, 02:35 AM)Arran Wrote: (08-26-2016, 11:56 AM)Eric T Wrote: These buttons would have looked really spiffy had they been back lit.
Philco missed out on a chance to jazz up this set.
Well, one could always rig up a warm white LED behind the pushbuttons running off the 6.3 volt filament winding, something easily removable, and which would not add too much extra of current load to the winding.
Regards
Arran Hmmmmm......
Very interesting idea.
It's not how bad you mess up, it's how well you can recover.
Users browsing this thread:
|
|
Recent Posts
|
|
Road Trip for a Philco 46-480
|
| Good morning, folks! I’ve finished the cabinet and the electrical restoration, and have detailed those in their respecti...jrblasde — 10:56 AM |
|
Studebaker/Philco AC-2687 car radio
|
| Arran,
Thanks for checking you manuals.
I appreciate that. Let me know what you find.
PhilPdouglaski — 08:46 AM |
|
Studebaker/Philco AC-2687 car radio
|
| I have some car radio service manuals, Riders I think (not to be confused with the big blue binders), so I may see if on...Arran — 01:20 AM |
|
Philco model 40-100
|
| Greetings;
Here is an update, I found a listing on fleabay for a similar chassis to yours, and it has a photo of what...Arran — 12:58 AM |
|
Philco model 40-100
|
| Greetings;
I think I may have found a clue as to what is missing, from a search I made, there is a rear view of the c...Arran — 12:12 AM |
|
Philco model 40-100
|
| I recently acquired a Philco model 40-100 farm (battery) radio. The radio was in very good condition except the red on f...mhamby — 05:59 PM |
|
Studebaker/Philco AC-2687 car radio
|
| Hello, Richard
the radio is an AC-2687 Studebaker model. The Philco model is S -5323 and the chassis p/n is S-5523Pdouglaski — 11:52 AM |
|
48-482 rear panel help
|
| The 48-482 is an AC only set as well, featuring a power transformer. While the transformer shouldn’t get “hot”, it is ye...jrblasde — 11:12 AM |
|
Studebaker/Philco AC-2687 car radio
|
| I gave a Chrysler/MoPar car radio from 1954, it was made by Philco, and it uses two chassis, one has the power supply an...Arran — 11:06 AM |
|
48-482 rear panel help
|
| Hello keithchip. You could make a hardboard back for the set, but make sure you provide plenty of ventilation holes in ...GarySP — 11:04 AM |
|
Who's Online
|
There are currently 758 online users. [Complete List]
» 1 Member(s) | 757 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
