Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Stromberg Carlson 430M
#31

All, I did find that the Screen Resistor on the 6K7 was supposed to be 82 K was reading 120 K.. I replaced it and now the Eye tube is much better. Seems to be responding better. On my strongest station now its almost completely closed.

Skip...
#32

Ok, Did a complete alignment using the AVC voltage to peak. Made good improvements.. Next is to start on the Cabinet.. Pictures to follow.. Will need help as I haven't never done this before..

Skip...
#33

Ok, Here are some pictures..

[Image: http://i292.photobucket.com/albums/mm38/...1jj7ea.jpg]

[Image: http://i292.photobucket.com/albums/mm38/...ih8jyp.jpg]

[Image: http://i292.photobucket.com/albums/mm38/...tbm9jn.jpg]

[Image: http://i292.photobucket.com/albums/mm38/...iwu7i8.jpg]

Ok its not in really bad shape. Would really not like to totally refinish it. Is there products that I can use to cover scratches Etc I plan on using Go-Jo first to clean it. Then What??

Skip...
#34

There are products like Howard's Restora-A-Finish that do some covering of scratches and smoothing of the lacquer finish but they are not miracle workers. It will look a little better for a little while. After a year or so it may need another treatment and it won't add lacquer where there is missing finish. It won't hurt to try it to see if it gives the look you want. There are a variety of colors including oak, neutral, maple, dark oak, walnut, dark walnut and mahogany to use depending on the existing finish.
#35

Ok I tried Howard's Restora-A-Finish.. It worked pretty good. Much better than it was..

[Image: http://i292.photobucket.com/albums/mm38/...ktymnb.jpg]

[Image: http://i292.photobucket.com/albums/mm38/...vrmdkj.jpg]

[Image: http://i292.photobucket.com/albums/mm38/...mdpicy.jpg]

[Image: http://i292.photobucket.com/albums/mm38/...5blcv2.jpg]

I do not know what to do with the dark edging around the top..

Still have to get paint off one side.. But doesn't look to bad for a 77 Year old radio..

Skip...
#36

that does look better!
#37

Yup, If the top looked as good as the sides I would be in business..

Skip..

Well I think I will put radio back in to see how it looks.. and sounds..I can always take it out again if I need to do more to cabinet..

Skip...




Users browsing this thread:
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently 2369 online users. [Complete List]
» 1 Member(s) | 2368 Guest(s)
Avatar

>