Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

16B volume control potentiometer
#1

I'm sure this has come up before but I can't find it anywhere, I'm looking for a replacement volume pot for my 16B, part # 33-5013 any info on what new pot to get would be helpful.  I'm finding conflicting info on values. Thanks.
#2

I suggest you try Mark Oppat at: http://www.oldradioparts.net

He has a huge selection of controls and will know the right one to use.

Jon
#3

Okay as far as I can tell the 16's started out with a 350,000 ohm pot with a tap at 30,000. that was changed at one time to a 2m with an unspecified tap. Nothing at radio daze list a tap and antique radio supply looks like all guitar stuff.
#4

http://www.oldradioparts.com/potindex.txt

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#5

Do you have 350K or 2M part? There were changes. I got mine from Mark.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#6

According to the 1946 IRC Volume Control Replacement Manual:

Part #33-5013 is 350K (75K tap). IRC equivalent D18-137X.

Part #33-5022 is 2M (500K tap). IRC equivalent D13-139X.

I also got a replacement from Mark Oppat.
#7

I have seen 2 different chassis in 16B Cathedral Radios
4 band and the 5 Band which is more common in the 16B

Not sure if VC are the same

Bob T
#8

(03-19-2017, 11:57 PM)Nathan Slingerland Wrote:  According to the 1946 IRC Volume Control Replacement Manual:

Part #33-5013 is 350K (75K tap). IRC equivalent D18-137X.

Part #33-5022 is 2M (500K tap). IRC equivalent D13-139X.

I also got a replacement from Mark Oppat.

[i] I have the 33-5013, I couldn't find anything on it. I opened it up and it looks great, I pulled the one out of my 16X and apparently the pots not the problem. Both work but I'm getting less than half the volume I should at max.[/i]




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM

[-]
Who's Online
There are currently 4312 online users. [Complete List]
» 1 Member(s) | 4311 Guest(s)
Avatar

>