1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Knob Labeling?
GregL
Junior Member
**
Posts: 41
Threads: 12
Joined: Jul 2013
City: Palm Springs, CA.
#1

07-07-2018, 03:03 PM
I am trying to determine if the on/off, volume, etc., knobs were originally labeled on my Model 507 Radiobar? I seem to have gotten mixed answers to this question. I have purchased the "Radiobar" front panel decal from Radio Daze and would like to have that, and any other correct decals installed by my cabinet restoration shop. 
I honestly cannot remember if the knobs were labeled when I first got the radio almost 50 years ago.
Your thoughts?
Find
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#2

07-07-2018, 03:26 PM
No, the knobs had no decals above them originally. The only decal on the front panel would have been the "Radiobar" decal with "PHILCO" underneath that.
--
Ron Ramirez
Ferdinand IN
Find
GregL
Junior Member
**
Posts: 41
Threads: 12
Joined: Jul 2013
City: Palm Springs, CA.
#3

07-07-2018, 04:51 PM
Thank you Ron. That seems to be the general consensus over at Radio Daze as well.
Although it does seem odd that Philco would not have labeled these controls originally.
Best, Greg
Find
« Next Oldest | Next Newest »




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Rusty Tuning Condenser
Give the tuner a good wash in Dawn and hot water. Then set tuner in a plastic container and cover with vinegar let soak ...David — 12:53 PM
Rusty Tuning Condenser
If you have rust between the vanes, I wonder how you get the NJ in between, and how you then wipe it off.morzh — 12:02 PM
Philco 60 Squealing
If the noise is still there, the OPT might just be OK. Or so we hope.morzh — 12:01 PM
Philco 60 Squealing
You would probably be replacing the OPT.RodB — 10:54 AM
Philco 60 Squealing
I have been playing the radio for a while now and doing well. Turned it on today and all I got was a whole lot of noise....dconant — 09:39 AM
Rusty Tuning Condenser
Thanks guys. I think I'll give the Naval Jelly a try since I can better control where it goes.dconant — 09:23 AM
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM

[-]
Who's Online
There are currently 3216 online users. [Complete List]
» 2 Member(s) | 3214 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios