Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 38-690
#1

I've been offered a 38-690 at a very low price. Don't know too much about condition, but I'm wondering about what repro parts are available for this model. First, I've not been able to locate a reproduction dial for it. I see one at Radiodaze for the 37-690, but the 38-690 isn't mentioned. Anyone know if there is a dial available? Also, am I dealing with photo finish on the cabinet? Finally, any opinions on this set? Obviously was high end back in the day, but is it worth restoring?
#2

Welcome to the Phorum!
Icon_wave

37-690s and 38-690s are generally thought of as the best sets Philco produced so a low price (depending on what low is) for one is a good deal unless its simply unrestorable.  I've never had the chance to work on one so some of the folks who have real experiences with them should chime in.  

No, there is not any photofinish on those sets...all veneer.  For future reference here's a list of sets with photofinish that Ron put together: http://www.philcoradio.com/phorum/showth...9#pid33789

I don't know about the dial, but if they (Radiodaze) don't have it, they can probably make one.  The other source is Mark Oppat http://www.oldradioparts.net/dials1.html  but he has not found a source for the amber dial materials and his 38-690 is out of stock.  
#3

Thanks for the info. I know that Mark was doing these dials along with Radiodaze, and I had heard that the amber material was gone. I don't know the overall condition of the set yet, so I'm just gathering some preliminary info. I'll hopefully be seeing the radio this week, so I'll know more once I get the chance to look it over.
#4

 I believe that the dial is the same as a 38-116, which would make sense since the RF sub chassis is the same apparently depending on which code number of 38-116 RF deck matches up with the 38-690. I think that the main difference between a 38-690 and a 38-116 is in the audio amp and power supply stuff, which is a good place to begin the electrical restoration I think.
Regards
Arran




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM

[-]
Who's Online
There are currently 3926 online users. [Complete List]
» 1 Member(s) | 3925 Guest(s)
Avatar

>