Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 42-350 dial pointer
#16

Just sent the photos. If you think it will work for you, you are welcome to have it. Glad to help.

1929 Victor R-32, 1933 60L, Phil 40-158, Phil 42-400X, Phil 47-1230 Radio/Phono,, 1950 Phil TV t-1104, Air King 4000, Philco 41-105, Philco 37-675, RCA Victor 9K2, PT-50, Phil 54C, PT-44 Cabinet, Phil 118X Cabinet

Gregg Icon_thumbup
#17

Gregg - I can't tell from the photo does it slide along a flat metal back plate?
#18

Terry I sent a few more pics. It slid across a glass dial. The top tee section where the dial cord runs through it sat on the top edge of the glass dial. The needle is slightly offset from the tee to make up for the thickness of the glass dial.

1929 Victor R-32, 1933 60L, Phil 40-158, Phil 42-400X, Phil 47-1230 Radio/Phono,, 1950 Phil TV t-1104, Air King 4000, Philco 41-105, Philco 37-675, RCA Victor 9K2, PT-50, Phil 54C, PT-44 Cabinet, Phil 118X Cabinet

Gregg Icon_thumbup
#19

I just sent a pic of it sitting on the glass dial to give you a better idea of how it was.

1929 Victor R-32, 1933 60L, Phil 40-158, Phil 42-400X, Phil 47-1230 Radio/Phono,, 1950 Phil TV t-1104, Air King 4000, Philco 41-105, Philco 37-675, RCA Victor 9K2, PT-50, Phil 54C, PT-44 Cabinet, Phil 118X Cabinet

Gregg Icon_thumbup
#20

Just got them.

I don't see any kind of notch or groove that would fit the metal plate I have but it the needle is certainly long enough.

Even if I have to "Frankenstein" into something I can use I think you at least solved the actual needle part of all this.

If you have a chance can you mail it to: Terry Lett  309 Four Seasons Drive  Mason OH  45040?

I really appreciate your help on this. I was making such good progress on the rest of the radio until I hit this snag.

Thanks again Gregg!
#21

Absolutely, I'll drop it in the mail tomorrow. Like I said if you can make it work, give it a shot. If you can't, throw it in a drawer like I did. Icon_smile

1929 Victor R-32, 1933 60L, Phil 40-158, Phil 42-400X, Phil 47-1230 Radio/Phono,, 1950 Phil TV t-1104, Air King 4000, Philco 41-105, Philco 37-675, RCA Victor 9K2, PT-50, Phil 54C, PT-44 Cabinet, Phil 118X Cabinet

Gregg Icon_thumbup
#22

You rock!
#23

Terry I mailed the pointer today, so you should have it Tuesday or Wednesday. I hope it works out for you.

1929 Victor R-32, 1933 60L, Phil 40-158, Phil 42-400X, Phil 47-1230 Radio/Phono,, 1950 Phil TV t-1104, Air King 4000, Philco 41-105, Philco 37-675, RCA Victor 9K2, PT-50, Phil 54C, PT-44 Cabinet, Phil 118X Cabinet

Gregg Icon_thumbup
#24

I can't thank you enough.

I'm sure I can make it work. The real challenge will probably end up stringing the new assembly.

Dial stringing is like slow torture.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM

[-]
Who's Online
There are currently 3589 online users. [Complete List]
» 3 Member(s) | 3586 Guest(s)
AvatarAvatarAvatar

>