1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco ~ 1942 meets 2009 ~
Drew
Junior Member
**
Posts: 25
Threads: 11
Joined: Sep 2006
#1

09-03-2009, 12:12 PM
Something to do with that extra console in the basement ? http://www.youtube.com/watch?v=z4WBTaz4NvY

Not sure if Home Radios is the right category for this, but here it is.
Find
batterymaker
Member
***
Posts: 104
Threads: 11
Joined: Oct 2005
City: Indianapolis, IN
#2

09-04-2009, 08:21 AM
....no comment. Icon_neutral
Find
kruc
Member
***
Posts: 54
Threads: 1
Joined: May 2006
#3

09-11-2009, 04:09 AM
I used to have a pirate Apple II motherboard, pwr supply, and 2 floppy drives mounted in an old IBM Selectric case. I also put a WE touchtone keypad and network inside a Kellogg wall phone, with cloth covered wiring of course. However, I hope that techno-nerd made sure the chassis went to a good home to enable someone else's console to work as designed.
Dave
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

[-]
Who's Online
There are currently 3198 online users. [Complete List]
» 2 Member(s) | 3196 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios